GottingenChain guide rail lifting cargo elevatorPrice sale
2024-03-16 01:06:39Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Gottingen,What is the pressure of the lifting platform? The movement of the lifting platform has always been our concern now. Our use occasions are uncertain, and most of them are part-time jobs. Therefore, in order to better favor customers, we are constantly researching lifting with good mobility. Platform, which can be used in different occasions, but for some large logistics companies or some enterprise processing plants, we are still used to using fixed lifts. It has a huge load capacity and is very stable and strong, which can meet the needs of many customers. This is also In recent years,GottingenProfessional guide rail type cargo elevator, domestic lifting platforms have been used.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Maha Sarakham,Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt it must be washed off with gasoline or thinner.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.
When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.What are the common faults of the hydraulic lifting platform The oil cylinder of the hydraulic lifting platform is seriously worn out. If the inner sealing ring is damaged unevenly or there are obstacles inside, it is easy to cause uneven force, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations,Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Walking: assisted self-propelled, self-driving, we need to check the foundation to see if there is any water accumulation and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Online consultation,Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.It is necessary to check the brake of the guide rail type elevator frequently, and there should be no dirt on the friction surface.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Gottingen,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door,GottingenChain lifting cargo elevator, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.