The other is designed with deformation angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore,Waynzil beckremsThick walled square tube, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Compared with other welding, square pipe welding has many advantages, mainly because of the exothermic reaction, the material only needs to be heated below the melting pointWaynzil beckrems,Formulate the documents stored by the square tube for a long time and implement them in accordance with.Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Pyetrykaw,The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.

Square pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.The standard number of spiral square pipe (standard of the Ministry of petroleum) for low pressure transmission is syt-. The representative materials are qbqb and other carbon steel materials. It is mainly used for low-pressure transmission of water, oil, natural gas, heating and other pipelines.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force iron wire section steel shot, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives It can also achieve the required uniform roughness.Meticulous workmanship, class II pressure pipe system,Waynzil beckremsGalvanized square pipe, boiler and superheater. It is a long-term business square pipe, square pipe,Waynzil beckremsCold galvanized square pipe manufacturer, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Strength QB square strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe is rolled in the annular pass composed of variable cross-section circular hole groove and fixed conical plug. Cold drawing is usually carried out on single chain or double chain cold drawing machine. This method is to put the heated pipe blank in a closed cylinder, and the perforated rod and rod move to extrude the part from the smaller die hole. This method can produce steel pipe with smaller diameter.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.

Strength QB square strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe is rolled in the annular pass composed of variable cross-section circular hole groove and fixed conical plug. Cold drawing is usually carried out on single chain or double chain cold drawing machine. This method is to put the heated pipe blank in a closed cylinder, and the perforated rod and rod move to extrude the part from the smaller die hole. This method can produce steel pipe with smaller diameter.demand,Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.First, remove the deposits on the surface of the square pipe surface with copper wire brush. Use the perfume oil or other scrubbing oil on the surface layer, or use phosphate or chromate solution, brush, spray or dip coating. After the fixed reaction time, rinse the acid solution with plenty of fresh water on the surface.Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.Waynzil beckrems,It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.