After the electric elevator passes the inspection, the user unit shall organize the leasing unit, installation unit, and supervision unit to conduct acceptance. For the implementation of construction general contracting, the acceptance shall be organized by the construction general contracting unit. The acceptance form should be signed by the relevant responsible person.The spacing between wall brackets and the height of guide rails above the high attachment point should comply with the requirements of the user manual.Donghe River,If the set screw is loose, be sure to pin it tightly to prevent accidents caused by the shaft pin falling off. Hydraulic oil should be kept clean and replaced every months.Setting requirements: The spacing of wall brackets along the vertical direction should comply with the provisions of the user manual.Glubokoye,Secondly, the lifting platform is driven by electrical energy and lifted by the hydraulic system. During operation, it is necessary to avoid irregular operations. To ensure the normal and orderly operation of the lifting platform and achieve the ideal unloading level, timely inspection of various functions is essential.The full height landing door should meet the following requirements: the net height of the landing door opening should not be less than m. In special circumstances, when the net height of the building entrance is less than m, it is allowed to lower the height of the lower door opening, but in any case, the net height of the lower door opening is not less than m. (Article of GB-)Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.

Chain type electric lifting mechanism: With a good guiding mechanism,Donghe RiverElectric elevator lifting 10 meters, it can ensure that the equipment does not tilt during operation. Gear and rack electric lifting mechanism: precise transmission and high cost.When a suspension cage with a rated load capacity acts on the buffer at a speed greater than the rated speed of .m/s, the average deceleration of the suspension cage should not exceed g,Donghe RiverElectric hydraulic elevator, and the time when the peak deceleration exceeds g should not exceedThe safety distance between the outer edge of the upper part of the landing door and the moving parts of the electric elevator during normal operation should not be less than .m; If the rated speed is not greater than .m/s, the safety distance can be .m.technical service,A complete lifting platform accessory can be selected and customized according to different places, venues, and environmental usage conditions. Meet the needs of different users. So why lifting platforms can be used and installed in so many industries and places is because they can achieve multi-purpose, demonstrate multifunctional, and win market demand. In modern industrial transportation processes, lifting platforms have begun to play an increasingly important role, whether in airports, docks warehouses, floors, workshops and other places that require rapid loading and unloading of goods, long-term operation and use of these devices inevitably lead to wear and consumption It has also brought great contributions to the entire industry and even the entire economic development. However, and regular maintenance and upkeep are essential. Otherwise, both work efficiency and utilization rate will decrease, and at that time the gains and losses will outweigh the losses.Stage equipment safety door. To prevent personnel from extending their heads, and feet out of the shaft and objects from falling into the vertical shaft. Its vertical position should be closed,Donghe RiverElevator electric elevator, its cabin should be full of doors, and the height of the hoistway (hall door) should not be less than meters; The electric door opening and closing switches should be removed from the vertical and passenger compartment doors. In order to prevent accidents caused by vertical, passenger car doors, the full width of the lifting passage opening should be covered.

Before operating the construction electric elevator, routine inspections should be carried out according to regulations and inspection records should be filled out.production,During loading and unloading, the horizontal distance between the edge of the cage door and the edge of the landing station should not exceed mm.Limit switches should be triggered directly by the movement of the suspension cage or its related components.The scaffolding of the parking platform should be laid tightly and firmly.Donghe River,It is understood that the scissor type lifting platform is a widely used specialized equipment for high-altitude operations. Its shear fork mechanical structure provides high stability for the lifting platform, wide working platform, and high load-bearing capacity, making the range of high-altitude operations larger and suitable for multiple people working simultaneously. The lifting power is divided into V, V or V power supplies, diesel engines, using Italian and domestic hydraulic pump stations, and the table top is equipped with anti slip insulation buckle plates, which have anti slip, insulation and safety features. Please rest assured to use.Pipeline rupture valve: When the hydraulic system pipeline ruptures and the car stalls and descends, it can automatically cut off the oil circuit and stop descentWhen the wall bracket adopts non matching standard products, design calculations should be carried out.