After hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.The installation personnel should have the qualification for installing hydraulic cargo elevators carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.Xinmin,There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature,XinminElectric hydraulic fixed lifting platform, the volume will change, which is reflected in the lowering of the position on the table.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found they should be promptly cleaned up.Vitti sur Seine,The main device does not engage. When this fault occurs, whether the internal and external emergency stop button switches the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.

Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, and there should be no leakage at all components,XinminHydraulic aluminum alloy lifting platform, pipelines, and joints.Any work carried out at a height of meters or above should be considered as work at height. Any work that can be done in advance on the ground must be done on the ground to minimize high-altitude operations.The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.equipment maintenance ,Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.The use of cleaning oil and the brand used in the system

Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.Superior quality,The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, only clean plastic plugs can be used to seal the end of the pipeline.A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve,XinminHydraulic lifting platform experiment, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.Xinmin,This paper briefly introduces some matters needing attention in the selection of oil tank for hydraulic elevators. The main functions of the hydraulic oil tank for elevators in the hydraulic system of elevators and hydraulic elevators and other hydraulic machinery are oil storage, heat dissipation, separation of air contained in oil and elimination of foam.The undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.