The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, the bearing capacity of specimens increases diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), American code (ACI -) and Japanese code (aij-cft), China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme, and establish quality standards.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Camoapa, series & mdash; Ferritic and martensitic stainless steel.All steel with openings at both ends and hollow sections, and with a large ratio of length to section perimeter, can be called steel pipe. When the ratio of length to section perimeter is small, which belong to the category of pipe products.Syzran,Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃ so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Stainless steel has two classifications: one is divided into chromium stainless steel and chromium nickel stainless steel according to the characteristics of alloy elements; The other is divided into m stainless steel, f stainless steel, a stainless steel and A-F duplex stainless steel according to the microstructure of steel in normalized state.In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.

Model & mdash; The addition of sulfur improves the processability of the material.Hydraulic saw grinding disc (manual saw wire cutting machine).At low temperature ferritic stainless steel pipe has low-temperature brittleness like carbon steel, but austenitic steel does not. Therefore, ferritic or martensitic stainless steel produces low-temperature brittleness, while austenitic stainless steel or nickel base alloy does not show low-temperature brittleness. Sus (Cr) and SUS (cr) of ferritic stainless steel pipe It shows that the impact value decreases sharply at low temperature. Therefore, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, high purification process can be considered. With the help of C and N level, the embrittlement temperature is in the range of - ℃ to - ℃High quality brand,When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle,Camoapa316 thin wall stainless steel pipe, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, so as to facilitate the observation of molten pool and penetration; when filling the welding wire,CamoapaPrice of 631 stainless steel plate, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.Construction materials shall be prepared and delivered to the site according to the data scheme, and shall be supplied according to the scheme.When improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.

Stainless steel why corrosion-resistant stainless steel decorative pipe, stainless steel pipe, stainless steel pipe, all metals react with oxygen in the atmosphere to form an oxide film on the surface. Unfortunately, the iron oxide formed on ordinary carbon steel continues to oxidize, expanding the corrosion and finally forming holes. The carbon steel surface can be guaranteed by electroplating with paint or oxidation resistant metals (e.g. zinc, nickel and chromium), but as is known, this protection is only a thin film. If the protective layer is, the steel below begins to rust.technical service,Add a small amount of sulfur and phosphorus to make it easier to cut.　　— Good ductility, used for molding products. It can also be machined to harden rapidly. Good weldability. The wear resistance and fatigue strength are better than those of stainless steel.When hoisting stainless steel pipes, public slings, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, electric arc traces and surface purification in the process of transportation, storage and processing, it must be completely cleaned, polished with an angle grinder, and then polished Polishing with optical sheet or metallographic sandpaper.CamoapaBidirectional Product Description: the tensile strength of the material is ~ mpa, and the high working temperature can reach ℃.When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price, the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel pipes have been recognized by the majority of customers. In the actual construction on site, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).All steel with openings at both ends and hollow sections, can be called steel pipe. When the ratio of length to section perimeter is small, it can be called pipe section or tubular fittings, which belong to the category of pipe products.