What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers,ChengdeGuide rail chain elevator, different materials, different rated loads, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Chengde,The main structure and application of the guide rail elevator: the mechanical part of the guide rail elevator mainly includes three parts: the lifting device, the track device and the belt changing device. The main function is to provide the moving track to make the operation more smooth. The belt changing device is used to switch the track when the elevator is going to pass the door. Lifting device The internal structure of the lifting device is mainly composed of gear mechanism, bracket, worm gear, guide mechanism, boom, upper and lower shells, etc. Gear mechanism The gear mechanism mainly includes large and small gears, a winding wheel, a middle shaft, and a safety device composed of a stop buckle and a torsion spring.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling and alignment to ensure the level of the foundation and various requirements for use.Meili, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform forceBefore the elevator manufacturer connects the motor to the elevator, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly then screw on the other two mounting bolts at diagonal positions, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.

The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Any product always has a running-in period when it is used for the first time, so what should we pay attention to during the running-in period of using the hydraulic lifting platform? Today, the editor will share this topic with you.After the goods are transported, clean up the debris on the platform.Market trend,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, the outer edge of the wheel hub, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.

The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.How much does it cost?,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, the editor will simply popularize the knowledge for everyone.The aluminum alloy lift is simple in design, beautiful in appearance and strong in practicability. It replaces the previous working methods of scaffolding and crane suspension. It has high working efficiency, safety and stability, and low failure rate.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers,Chengde5-ton factory lift cargo elevator, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity,ChengdeHeavy industry guide rail type cargo elevator, etc. effectively solving the difficulties of various lifting operations in industrial enterprises, strict testing so that Production operations freely. The professional elevator factory has advanced technology, more affordable prices, and more discounts are in progress, welcome to consult.Chengde,Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)After the goods are transported, clean up the debris on the platform.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.