When using the submersible slurry pump, which can be replaced without disassembling the slurry pump.Santa Ana,Santa AnaVertical slurry pump,　　 The fire control cabinet has fault alarm . When a single fire pump is working, power circuit failure, resulting in damage to the fire pump. Using the fire control cabinet, the alarm of the control cabinet can remind each　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.Bosanska Gradiska,　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　 Next, the water seal, lock ring and other parts need to be installed.　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.

　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 others　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.How many?　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation

　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from oneHonest management,　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　 Pipeline single-stage single suction chemical pump. Pipeline pump used for transporting chemical corrosive liquid in textile, pharmaceutical,Santa AnaAh slurry pump, health, food, chemical, petroleum, oil refining and other industries, with the service temperature not higher than ° C. It is an ideal product to replace the traditional chemical pump.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)Santa Ana,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income and provide material conditions for agricultural mechanization and water conservancy.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, the water supply is not satisfied or the bottom valve is not closed tightly, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.