First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re usingburnaby ,　　 Transmission part all kinds of horizontal slurry pumps adopt the same series of transmission parts, including bracket and bearing components. The pump shaft has large diameter, good rigidity, short cantilever, and will not be bent and vibrated under bad working conditions. Heavy single row or double row conical roller is selected for the bearing according to the transmitted power　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this,burnaby Submersible sewage pump, it and the generator naturally become popularGuarabelat,　　Therefore the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.　　So it is called: submersible slurry pump.　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.

　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　In fact, stainless steel is not only advocated in the medical industry, etc., and handle it at any time.Where can I find it?,burnaby Screw deep well pump,　　What is the order.　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　 the submersible slag pump is often used to transport pulp containing solid particles,burnaby Drilling fluid slurry pump, so the wear resistance of the pipeline should also be considered.

　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use,　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump　　 When the electric pump is not in use take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so thatburnaby ,　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades but pay attention to adjusting the vacuum pump　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve