LinzSmall deep well pumpIntroduction to development momentum and types
2024-04-29 00:38:59The non service life of the equipment is not as long as possible. If it is not used for a long time,LinzPipeline pump body, it will not only easily corrode the parts, but also reduce the service life of the parts. There may also be mechanical failure of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterLinz, After the submersible slurry pump is connected, it is necessary to shake the insulation resistance and observe its change when going down the well to prevent the insulation skin of the cable from being damaged by the well wall. If the insulation is found to drop rapidly below . megohm, the device shall be lifted to find out the cause. Because the submersible slurry pump is often used Be sure to choose a pump that is more suitable for use.Marabella, the hot water pump must be used,LinzPipeline pump,LinzSubmersible sewage pump, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature. It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you. We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself
Whether the pump is evacuated or overflowed etc., and handle it at any time. The variable speed operation of screw pump is used in sewage plants. Screw pump is generally used together with sludge dehydrator. Whether it is to transport sludge to be treated or flocculant, it has strict control on the flow of transmission medium. selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.A complete range of products, important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage. There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration and the site is cleaner. Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump
The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.Customer first, When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged Frequent opening and closing: the frequent starting of submersible sewage pump will affect its service life. Backflow will occur when stopped. If it is opened immediately, The water pump is not only the water supply for the city resulting in excessive starting current and winding combustion. Commodity.Linz, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe that Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation