In addition the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in useInnsbruck,　　There is a blockage in the water pump.　　So it is called: submersible slurry pump.Boke,　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.

　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet that is, the traditional slurry pump cannot be installed and operated,InnsbruckSubmersible pump can pump sewage, and the submersible slurry pump can supplement this part of the blank work point.　　The sheath is divided into front sheath and rear sheath, so it has good wear resistance. It can be used until it is worn out, so as to prolong the maintenance and replacement cycle and reduce the operation cost. The outlet of this series of pumps can be installed at angles　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise,Open the gate valve.Honesty and mutual benefit,　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties,InnsbruckWQ submersible sewage pump, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.

　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, which will also increase the sand pumping area. This will also increase the sand pumping area so there will be no buried pump when it is used. However,Quality risk,　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　 within the estimated installation depth, the minimum inner diameter of the well is mm　　Only in this way can its service life be extended to a large extent.Innsbruck,　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment