Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.Detroit,　　It is not allowed to operate the electric pump under the condition of low lift for a long time (generally, which shall be controlled within the recommended operating lift plan as far as possible to prevent the electric pump from burning out the motor due to overload. Pumps without self circulating cooling equipment prevent all of them from being exposed to the water for a long time　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller,DetroitBooster pipeline pump, the liquid effect is on the auxiliary impellerMatola,　　The Tao part also consumes part of it.　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　Whether the pump is evacuated or overflowed,DetroitPipeline pump, etc., and handle it at any time.

　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,　　Automatic pump failure: cause: A. whether the frequency converter has abnormal symbols; b. Whether the actual pressure is higher than the set pressure.　　The utility and durability of the utility model so the polymer composite materials are generally used in production.manufacturer,　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated power

　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.Sales Department,　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, and pay attention to the temperature rise outside the packing chamber.Detroit,　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.