KielMany electric hydraulic elevatorsTalking about the matters needing attention in maintenance
2024-04-07 00:25:08Equipped with a manual descent valve for emergency descent in case of power outage.Elevator: The fully automatic high-altitude work platform has a sturdy structure, which minimizes the deflection of the high-altitude work platform. Equipped with automatic walking function,KielMobile hydraulic lifting platform, it can walk in different working states without the need for external power supply. The handle can walk at an adjustable speed, and easy lifting. Only one person can complete forward, backward, turning, fast, slow walking, and up and down movements, saving labor and effort. Can be designed and produced according to user requirements.Kiel,It is stipulated that measures should be actively taken for renovation.The hydraulic power unit adopts an integral pump station, with a compact structure and reliable performance.Wevelgem,Made of high-strength rectangular steel pipes, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.The person in charge of the work should not only inspect the condition of the vehicle and the operators, but also be responsible for checking the terrain environment and whether the descent meets the requirements of safety technical measures or pre developed work plans. If there is any discrepancy, corresponding elevator measures should be formulated before starting work.Made of high-strength rectangular steel pipes, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.
Secondly, frequent voltage instability can directly burn out the power unit motor. The consequences of motor burning are very serious, which can lead to an instant decrease in pressure. If the equipment is not equipped with safety devices such as relief valves or explosion-proof valves, it can cause the lifting equipment to fall, leading to accidents. At the same time, replacing a new power unit also requires a certain cost.Scissor fork type, cylinder sleeve type, multi column type, curved arm type elevator (replacement of folding arm type), chain type elevator (elevator, cargo elevator).Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Fill the above components with oil. The service life of bearings can also be greatly enhanced.Scheme customization,Equipped with a manual descent valve for emergency descent in case of power outage.Enhance the lift functionElevator operation status: The elevator products are made of high-strength and high-quality materials, which can be divided into single masted, double masted, three masted, four masted, and six masted types according to the lifting height. Generally, single masted types are used when the lifting height is below meters, and three masted or four masted types are used when the lifting height is between meters and meters.
Summary: Elevators can be large or small, and regardless of size, there should be no sense of luck during operation. It is necessary to establish correct safety awareness in order to ensure safety.How many?,The lifting drive chain is a double chain structure, using industrial plate chains with high bearing capacity and safety factor.Overvoltage, undervoltage, and phase fault protection. Overvoltage, undervoltage and phase fault protection devices operate when there is a voltage drop, overvoltage, or phase fault or phase fault in the electrical circuit, and the construction elevator stops running. Some construction elevator maintenance personnel on construction sites do not promptly eliminate the malfunction of the overvoltage,KielHydraulic elevator structure,Kiel4 meters, undervoltage, and phase fault protection device, but instead cancel or short-circuit the protection device to make it ineffective, leaving a hidden danger of accidents for the equipment. Some early products do not have this protection device at all, and it is recommended to equip it. The construction elevator should be able to carry people and objects only when the overvoltage undervoltage, and phase fault protection devices are reliable and effective.With the strict control of high-altitude construction by the country, safety production is becoming increasingly important. As a highKiel,Firstly the maintenance process should be carried out on the premise of ensuring the safety of staff. Before repairing the elevator, the power must be disconnected, and the power must be verified and hung up; No power transmission, people working quo; Identification plate for. During the maintenance process, it is not allowed to disconnect the grounding wire of the elevator. If it is necessary for maintenance work, after the maintenance is completed, the grounding wire must be connected before the power test can be conducted. When replacing elevator spare parts, it is necessary to ensure that the spare parts are availableSingle masted elevators are widely used in factories, hotels, restaurants, stations cinemas, exhibition halls, and other places. They are a good safety companion for maintaining equipment, painting and decorating, replacing lighting fixtures, electrical appliances, cleaning and maintenance, and other purposes.Characteristics of elevator form:.