. Domestic wce cerium tungsten electrode is used for electrode data. The shape and diameter of the end of cerium tungsten electrode have a great impact on the fluctuation of welding process and weld formation.In engineering, the following methods are often used to prevent intergranular corrosion: reduce the amount of carbon in steel so that the amount of carbon in steel is lower than the saturated solubility of austenite in equilibrium, that is, fundamentally solve the problem of precipitation of chromium carbide (crc) on the grain boundary. Generally, the requirement of intergranular corrosion resistance can be met when the amount of carbon in steel is reduced to less than .%.Chatelet,Ti-a alloy with improved titanium and overall corrosion resistance has been used to manufacture u and Pu solution evaporation boilers and heat recovery evaporation boilers in Donghai reprocessing plant, because zirconium has stable corrosion resistance in the environment,ChateletStandard for stainless steel pipe, zirconium is used in its continuous dissolution tank in the reprocessing plant in liusuo village, Aomori County, Japan. The US Academy's ruling that the countervailing duty is not suitable for products from non market economy countries has just given China's steel pipe enterprises a little relief. The anti-dumping stick from the EU has given a heavy blow to hundreds of domestic stainless steel pipe manufacturers.It has the characteristics of high efficiency and low cost. At the same time, it can also well ensure the welding quality (in the capacity expansion and reconstruction project of Urumqi petrochemical, we use this method to weld joints and repair joints, with a one-time qualified rate of welding), which is worthy of our use.Hirna,The product quality advantages of continuous casting billet of stainless steel pipe fittings are mainly reflected in that the non grinding rate of the outer surface of the billet except the head and tail section has reached more than %, and the total surface grinding yield has reached %. In order to achieve this goal, it is necessary to refine the molten steel, achieve low oxygen and sulfur content, do a good job in the metallurgy of the ladle and tundish accurately determine the molten steel temperature, Further reduce the inclusion content.Stainless steel has been used as a structural material for building new buildings and repairing historic sites for more than years. Early designs were calculated according to basic principles. Today and realize no oxidation casting, design codes, such as ANSI as of the American Society of civil engineers, are usedThe shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).

After that, the second widely used steel is mainly used in food industry, pharmaceutical industry and surgical equipment. Adding molybdenum makes it obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than stainless steel pipe, it is also used as & ldquo; marine steel & rdquo;. SS is usually used in nuclear fuel recovery devices. Grade stainless steel Steel pipes usually also meet this application level.The external anti-corrosion coating of stainless steel shall be galvanized and epoxy asphalt coating or coating with higher requirements according to the soil conditions of the pipe laying ground.The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.quality standard,Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection (i.e. solid core welding wire + TIG + water-soluble paper)Construction materials shall be prepared and delivered to the site according to the data scheme, and shall be supplied according to the scheme.Therefore,ChateletPrecision stainless steel coil, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.

AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.device management,With the implementation of China's reform and opening up, and a large number of urban houses, public buildings and tourism facilities have been built, which puts forward new requirements for hot water supply and domestic water supply. In particular, and the requirements are also increasing. Galvanized steel pipe, a common pipe, will gradually withdraw from the historical stage under the influence of relevant countries because of its corrosivity. Plastic pipe, composite pipe and copper pipe have become common pipes in the pipeline system. However, under certain circumstances, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm. In high-quality drinking water system,ChateletPrice of 316L stainless steel strip, hot water system and water supply system that puts safety and sanitation first, it has the characteristics of safety, reliability, sanitation, environmental protection, economy and applicability. It has been proved by engineering practice at home and abroad that it is one of the new, energy-saving and environmental protection pipes with good comprehensive performance of water supply system. It is also a very competitive water supply pipe, which will play an incomparable role in improving water quality and people's living standards.Low temperature embrittlement --- in low temperature environment the deformation energy is small. In the low temperature environment, the phenomenon that the elongation and area shrinkage decrease is called low temperature embrittlement. Most of them are produced on the body centered cubic structure of ferrite series.When using this method, it should be noted that the water-soluble paper should be double-layer and must be pasted well, otherwise it is easy to cause damage and fall off of the water-soluble paper, resulting in loss of argon protection of the inner weld and oxidation, resulting in cutting of the weld junction and re welding, which can not ensure the welding quality and seriously affect the construction period. Therefore,Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe, mm.After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.When the stainless steel pipe with solid core welding wire is prefabricated, and the ventilation is very easy. At this time, the blocking plate is usually used to block both sides of the welded junction in the pipe and the bottom welding is carried out for the protection of ventilation (see Table ), and the outside is blocked with adhesive cloth.