Flux coated welding wire (self shielded welding wire) shall be used for backing TIG welding.The back is not protected by argon, and the flux cored wire + TIG process has been applied in China for several years. Flux cored wires such as et-elt-et-elt-t-et-elt- have been produced and applied to field welding, and good economic benefits have been obtained.Hoboken,The Chinese brand of stainless steel plate is crnimoti (CrNiMoTi with paper should also be this brand). The new brand is crnimoti stainless steel plate. The stainless steel plate is added with Ti in SUS steel to improve the intergranular corrosion resistance. It is applied to the equipment of, acetic acid and acetic acid.Stainless steel seamless steel pipe for structure (instead of gbt-)Emmen,The welding of stainless steel pipe is usually composed of backing welding, which is not only related to the quality of engineeringTypical ferritic stainless steels are Crl, Cr and Cr.The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.

Marking: in order to make the steel pipe complete the socket of the pipe fitting, the length must be marked and marked at the pipe end.In order to ensure that the mechanical properties such as yield strength, tensile strength, elongation and hardness of various stainless steel coils meet the requirements the stainless steel coils must undergo heat treatment such as annealing, solution treatment and aging treatment before delivery. The corrosion resistance of stainless steel coil mainly depends on its alloy composition (chromium, nickel, titanium, silicon, aluminum, etc.) and the internal structure of stainless steel coil,The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Highly recommended,. Raw material problem of stainless steel pipe. If the hardness is too low,HobokenStainless steel tray with hole, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.After that, the second widely used steel is mainly used in food industry, pharmaceutical industry and surgical equipment. Adding molybdenum makes it obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than stainless steel pipe, it is also used as & ldquo; marine steel & rdquo;. SS is usually used in nuclear fuel recovery devices. Grade stainless steel Steel pipes usually also meet this application level.In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore,HobokenThin wall stainless steel pipe, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity, so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Scheme customization,Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.Cold drawn (rolled) seamless steel pipe: round billet → Heating → Perforation & rarr; Lead & rarr; Annealing & rarr; Pickling → Oiling (copper plating) → Multi pass cold drawing (cold rolling) → Blank tube & rarr; Heat treatment & rarr; Straightening & rarr; Hydrostatic test (flaw detection) → Mark & rarr; Warehousing.Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and ,HobokenStainless steel shower pipe, martensitic stainless steel is marked with and C, dual phase (austenite ferrite).Hoboken,Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, change the included angle between the welding handle and weldment and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.There are three main reasons for oxidation of stainless steel: production process, which is one of the reasons for oxidation of steel products. In terms of production process and product characteristics, forming a thin oxide film on the product surface is the basic process to avoid oxidation, and it is also one of the main characteristics of steel products different from other steel products. It is specialized in products, renewable resources business and business package Including: stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe. However, when the oxide film is incomplete and discontinuous due to insufficient or negligent production process, the oxygen in the air will directly react with some elements in the product, resulting in the appearance of oxidation of the product.