The Tao part also consumes part of it.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Yaguajie,　　Select an appropriate flow according to the water inflow of the well or pool or the water consumption required by the actual engineering system. During model selection, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any timeVoula,　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as

　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　The microcomputer controller of the water pump control cabinet displays E: cause: the parameter of the microcomputer controller is edited incorrectly.　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!Promotion,　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　What is the cause of pump overload.

　　The application of pumps involves all aspects of work and production,YaguajieRubber lining submerged slurry pump, and the types of pumps are also diverse. Some of the same pump have several names and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the twoAnalysis project,　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　 The fire control cabinet has fault alarm . When a single fire pump is working, it is not easy to be found in time in case of insufficient water source,YaguajieCorrosive pipeline pump, power circuit failure, etc., resulting in damage to the fire pump. Using the fire control cabinet,YaguajieIrrigation deep well pump, the alarm of the control cabinet can remind each　　Rate.Yaguajie, some people outside the industry misunderstand this. In fact the correct application is very important. Due to the limitation of the name of the slurry pump the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　What is the solution to this situation?　　 When the power supply voltage is too low, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be