Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　Pump, sewage submersible pump and seawater submersible pump.Palma Soriano,　　Note: Motors for special environment can be customized according to the contract.　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.Beit Jann,　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　When the slurry pump is working, the pump needs to be placed on land, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, and the pump must be fixed when it is put into the water. Otherwise, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar % ore slurry %; It can be operated in series according to the needs of users.　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation, and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller, conical sleeve, and remove the guide housing. In this way, the impeller, guide housing, upper guide housing,Palma SorianoSelf priming slurry pump wholesale, check valve, etc. are unloaded in turn.　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely,Palma SorianoCentrifugal slurry pump, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and writeCreate brilliance,　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, the water begins to vaporize and change from liquid to gas. On the contrary when the temperature rises to a certain value, at a certain temperature, the pressure drops to　　Stability and reliability of seals between pump bodies.

　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable,Palma SorianoScrew deep well pump, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature high pressure and low temperature.High value,　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　In the process of daily use, the s of these two sewage pumps are actually the same. The biggest difference between the two is that one is fixed and the other is mobile. WQ series submersible sewage pumps are generally equipped with an auto coupling device, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.Palma Soriano,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.