economizers

Judged as failing.Heating surface pipes, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Sanshui River,Recently, the price of zinc has been falling continuously. The key reason lies in the soft skin of galvanized pipe consumption and the slow start of production and marketing rate of manufacturing industries in the middle and lower reaches after the Spring Festival. The disadvantage of zinc price has long been far beyond the level of cyclical factors. The main performance of no prosperity in the hot season is whether the market situation in the off peak season will become a more worried problem in the galvanized pipe sales market.Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Machala, Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system,Sanshui River45 large diameter thick wall seamless pipe, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method. Frame line crack

Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc. Pickling: if the material cannot be removed after cleaning pickling will be selected. Pickling of galvanized pipe is divided into chemical and electrolytic. How to prevent white rust of galvanized seamless steel pipe? It has a certain anti-corrosion effect on the pipeline.H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.Quality department,When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.

Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption, small types, multi specifications and high precision. Therefore, it is widely usedMarketing Department,Sanshui River15 how much is the price of galvanized pipe per meter,Because alloy pipe is a very unique pipe fitting we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.On the other hand, when the steel structure changes during heat treatment, that is, austenite transforms into martensite, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. Due to the change of tissue stress, the tensile stress on the surface and the compressive stress in the heart are just opposite to the thermal stress. The magnitude of microstructure stress is related to the cooling rate shape and chemical composition of martensitic transformation zone materials.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Sanshui River,I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.