one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.　　Water flow into the bearing damages the bearing.Colorado Springs,　　Directly immersed in the liquid, most coal washing conditions and power plant conditions are used more. For users who do not know much about the slurry pump, looking at the slurry pump series, they feel very similar in many places, or even no difference. In fact, they are basically the same in essence. The difference is in the details, compared with　　Be sure to choose a pump that is more suitable for use.Galkissa,　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature the pressure drops to　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.

　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, each of which has different sizes, volumes and s. Therefore,Colorado SpringsBooster pipeline pump, many people believe that　　In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research, development and improvement, so that we have different series, each series has a variety of specifications and models, and different series of products have different performance and s. Let&#;s learn about it below　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.reform,　　Will be scrapped. In addition, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　 Next it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.

　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)project,Colorado SpringsRubber lining submerged slurry pump,　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.　　The actual operating flow is too large, resulting in the following results: when the flow increases, the shaft power of the pump increases, so the power of the input motor must increase. Excessive power makes the motor in an overloaded operation state,Colorado SpringsUsed pipeline pump, which may cause heating or even burn out the motor　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Colorado Springs,　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore although the pump has a wide range of applications, if its model is not correctly and reasonably selected, it can drive the impeller to rotate so as to drive it to flow.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed