In this category, it can be shown that it is a relatively safe commodity.In addition, it should be noted that the release of formaldehyde must take a whole process of time. The formaldehyde content tested at this stage does not represent the long-term formaldehyde content.SPC floor is an economical floor material. Consumers can enjoy the texture of wood grain or stone grain in use without being bothered by noise.According to the requirements of consumers for sound insulation, blocks, plates or coils can be selected.Floor lacquer cloth, also known as floor leather (not PVC plastic floor), is a kind of paving material. It belongs to rubber plastic products. It is one of the indispensable floor materials for the decoration of power distribution room, substation and communication room. The thickness is -mm. Other thicknesses can be made according to the needs of users. The wear-resistant layer is generally less than or equal to .mm.The choice of lacquer cloth products shall be selected according to the suitability of the site.For example, the size of the product is determined according to the space of the house and the size of the place of use.At the same time, pay attention to the different places of use, and the selected patterns should also be different.For example in places that need to be kept clean, mm and mm;The total thickness (referring to the base material, intermediate layer and surface wear-resistant layer) is divided into mm and mm;The length of each roll of floor leather is m and m.Other specifications and dimensions can be determined by the supplier and the buyer through negotiation.Because of the requirements of production, each roll of floor paint cloth is divided into several sections (the patterns between each two sections are misplaced), so the length of the small section of a roll of floor paint cloth with sections shall be indicated, and the length of the roll of floor paint cloth shall be increased by at least cm (i.e. not less than two complete patterns).Generally, there can only be one section for high-quality products, and the number of sections of each volume of first-class products and qualified products shall not exceed ;The length of each section of first-class products shall not be less than m, and the length of each section of qualified products shall not be less than m.When inspecting the appearance quality of floor paint cloth leather, it should be visually inspected obliquely under the scattered sunlight or fluorescent lamp with the illuminance of ( ± LX and LM away from the tested sample.First, observe whether there are cracks, it can be determined that the floor leather is unqualified.The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. What cannot be observed are excellent products and first-class products;If it is slight but not obvious, it is deemed as qualified. Go back to the third step to observe whether there are missing patterns on the surface of the floor leather and whether there are defects of the transparent wear-resistant film on the surface. If there is no it is the first-class product and the first-class product. If there is slight missing or lack of film, it is the qualified product, otherwise it is the unqualified product.Finally, whether there are color differences in different parts, whether the superior products are uneven, and if there are the above two defects, the first-class products are those with but not obvious, and the products with obvious above defects but do not affect the overall beauty are determined as qualified products.Finally, based on the above judgment, the appearance quality of ground lacquer cloth is determined.The plastic coil floor paint cloth shall roll the wear-resistant layer outward on the pipe core and shall be externally packaged.The product name, manufacturer name, product mark, grade batch number, quality and length shall be marked at the obvious place of each package.In addition to the above three items that can be directly judged by the senses, attention should also be paid to the physical properties when purchasing floor leather to ensure its service life.Klostersburg, Select water resistance. Keep the floor dry and clean. If there is dirt on the floor surface, generally wipe it dry with a damp mop without dripping water.Doboy, Green environmental protection Good wear resistance and stability Pay attention to the size.

The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.The influence of foundation materials on the price of reinforced base plate.Strengthening the middle layer is mainly the base, and the method to distinguish the base material is good or bad.You can cut off the garbage with the merchant to see if it is white. The whiter the better.Generally, the base plate of reinforced floor accounts for most of the price of reinforced floor.High priced laminate flooring is a good base material. Mixed pine is used as the base material for second-line and third-line brand flooring. Of course, the production cost is not high, and the price of laminate flooring can also be borne.SPC floor has a thickness of mm-mm, and the weight per square meter is only about -kg, which is less than % of ordinary ground materials. It has incomparable advantages in building load-bearing and space saving in high-rise buildings.At the same time, it has special advantages in secondary decoration and transformation.Executive standard,SPC floor does not use strong glue in the production process, so there are no indoor formaldehyde benzene and other harmful substances.The indoor formaldehyde emerald green floor is not easy to cause damage to the body.Select well-known brands;Defects: small blisters can not be repaired after damage, and the upper foot is poor.

Super wear-resistant. The wear-resistant layer on the surface of SPC floor is a transparent wear-resistant layer processed by high technology, and its wear-resistant revolution can reach about revolutions.According to the thickness of wear-resistant layer, the service life of SPC floor is more than - years.SPC floor is a long-life floor especially suitable for public places with large flow of people and high degree of wear.Job description,Many people think WPC floors are thick and therefore durable.OK, it&#;s a durable floor, but no more than SPC floor.Compared with WPC flooring, SPC flooring has good density.The higher density makes them resistant to damage and heavy weight.They will not be affected by the falling or moving of heavy objects.Therefore, SPC is considered to have good durability.When scraping,KlostersburgSPC floor size, lift up all the furniture instead of pushing and pulling.The best protection is at the bottom of the furniture legs.In addition, if you have a refrigerator, piano and other heavy objects at home, you&#;d better share the weight with a protective pad.The combination of hardness and softness.The wood floor in the living room should be made of boards without knots,KlostersburgWhat brand is laminate flooring good, cracks and mildew. Generally, Fraxinus mandshurica, camphor and teak are better, because their lines are beautiful and clear, and their texture is moderate.The laying method of wooden floor is not very difficult, but it is required to have a certain carpentry foundation.Firstly the wood board shall be processed into the length and width coordinated with the room size according to the room size, and the floor shall be cleaned before laying.When laying, draw the center point and vertical and horizontal vertical lines of the room, and lay from the center to the four sides. glue and an appropriate amount of cement can be used for bonding between laths.Note that the glue must be coated evenly to avoid the warping of the plate.Klostersburg, Deformation level.The floor paint cloth is easy to age under the action of light and heat, the floor is hard and the surface color changes, so it is generally paved indoors and on the ground where the sun is not direct. The storage temperature is preferably ℃ ~ ℃. In order to prolong the service life of the floor paint cloth and maintain a long-term beauty, daily maintenance and maintenance are also very important. First, keep the board surface clean and free of sand and dust friction on the board surface; prevent pollutionThe objects shall be removed in time. Pay attention not to scrub with aone, cyclohexanone, concentrated alkaline water and other organic solvents to prevent color fading, degumming, cracking or warping of the surface. They can be wiped with detergent or detergent. They shall be cleaned with semi dry mop on weekdays to prevent dirty water from penetrating into the joint and damaging the bond.What is the difference between solid wood flooring and solid wood composite flooring?