Welding,St-Johns420J2 stainless steel plate, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.According to the purpose, it can be divided into oil well pipe (casing, pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe, geological pipe, chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.St-Johns,Stainless hot plate (grade I) GB- stainless cold strip (grade I)Bidirectional Product Description: the tensile strength of the material is ~ mpa, and the high working temperature can reach ℃.General-Escobedo,Continuous casting shall be adopted for stainless steel pipe fittings so as to improve the comprehensive yield, and cooperate with out of furnace refining, which significantly improves the production efficiency, omits the blank opening process and saves a lot of energy consumption.Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Meet the needs of architects and structural designers.

Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Usage: widely used in automobile, tractor and other industries.Production process of stainless steel welded pipe: raw material - strip - welded pipe - end repair - polishing - Inspection (spray printing) - Packaging - shipment (warehousing) (decorative welded pipe).how much, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.Application field: tubular boiler for pipeline in harsh seabed environment product description: ultra (ultra) critical unit is the basis of modernization of power generation equipment and energy conservation and emission reduction. Among the important pressure parts of ultra (supercritical) boiler, superheater and reheater are the parts with high working temperature and bad working environment. Previously, all such materials used in China were imported from abroad, while only steel material manufacturers in the world have limited capacity. Such materials have a large gap, expensive import prices, difficult procurement and short supply,St-Johns304 stainless steel strip, which seriously affected the production of ultra supercritical boilers and the development of electric energy in China. At present, China's demand for utility boiler tubes is about tons, and with the continuous improvement of ultra (supercritical) power generation technology, the demand is expanding. Several large domestic enterprises have invested a lot of human and financial resources in the R & D and production of such products, and have made considerable achievements. On the one hand, it has made its own contribution to the development of national electric power industry, its advantages are obvious, mainly for its simplicity and low cost, which is suitable for installation on the construction site. However, due to its structural characteristics, flux cored welding wire has high requirements for welders during operation, with fast wire feeding speed and high wire feeding accuracy. It is difficult to master. Welders should be specially trained and skilled before they can participate in welding in Yangba, Nanjing And foreign construction sites, we have successfully solved the problem that argon cannot be passed through the junction and repair port.manufacturer, so as to improve the comprehensive yield, and cooperate with out of furnace refining, which significantly improves the production efficiency, omits the blank opening process and saves a lot of energy consumption.The surface of the steel strip in the state of supply shall be rough or bright.Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die,St-Johns2507 stainless steel strip, and the jaw is perpendicular to the pipe axis.St-Johns,Deburring: after the pipe is cut off, the burr shall be removed to avoid cutting the sealing ring.Chloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).