The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　Submersible slurry pump In addition, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in useLittle goat,　　Belt drive shaft seal: the pump seal can be divided into three types: packing seal, auxiliary impeller seal and mechanical seal. The packing seal and the secondary impeller seal will drip during the operation of the pump. Mechanical seal can make no water leak.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,Comoros,　　Screw it down, and then remove the bearing inner race, O-ring, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment,Little goatBooster pipeline pump, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment

　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water and the pump needs to be started. Due to special structural requirements, the slurry pump and submerged slurry circulating pump need to be placed above the water surface when the slurry pump motor is submerged in the water so they need to be fixed, otherwise the motor will fall into the water　　Although they are both pipeline pumps among centrifugal pumps, there are still many categories. Next, let&#;s talk about some models of pipeline pumps and their respective uses.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.demand,Little goatSmall deep well pump,　　Submersible slurry pumps are mainly used in mining, metallurgy, coal,Little goatDeep well submersible pump, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　There are differences.

　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Supply chain quality management,　　What is the cause of pump overload.　　What faults will the water pump control cabinet often encounter in use? The water pump cannot work: cause: a. the power supply is not connected or the output phase of the control cabinet is missing; b. The water pump has been burnt out, and the water pump can not supply water: cause: A. whether there is water in the pool; b. Whether there is gas in the pump body that is not discharged; c. Inlet and outlet water　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.Little goat,　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.