Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pumpplace,　　Vertical pipeline centrifugal pump is a kind of pipeline centrifugal pump with vertical structure. There are many models of this pump. The common one is ISG pipeline centrifugal pump. This pump is also very widely used. It is often used in industrial and urban water supply and drainage and pressurized water supply in high-rise buildings. And in the　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor andAndapa,　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　First,placeVertical slurry pump, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　It is also necessary to clean the ventilation duct to avoid blockage.

　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles,placeHorizontal slurry pump, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should chooseSafety and health,　　The slurry pump of underground pump can also work normally.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use

　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, the place where it operates will also be limited. If the equipment willsuperior quality, and the leakage probability does not exceed drops /min hydraulic and other professions; The mechanical seal is tight and reliable, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　The following inspection shall be carried out: whether there are sundries between the impeller and the pump body due to too tight packing.　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.place,　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then when transporting some media with special properties, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.