CaborojoSewage pump diving,

　　The purpose is to avoid water leakage of the pump but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it tooCaborojo,　　Damage to the rotor.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.Bobo Dioulasso, it is necessary to regularly maintain the submersible slurry pump and replace the seals.　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.

　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　 Constantly observe the instrument, check the electrical equipment, and measure the insulation resistance every half a month. The resistance value shall not be less than . megohm.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.Convenient and efficient,　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.

　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beHow much is it,CaborojoSmall deep well pump,　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.　　Tighten the terminal blocks.　　The whole packing body,CaborojoVertical centrifugal slurry pump, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vaneCaborojo,　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds