The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professionalQuaximarpa,　　 Service conditions　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Attock City but such underwater depth is not the best operating depth of this kind of pump,　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.

　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　 Constantly observe the instrument, check the electrical equipment,QuaximarpaSubmersible pump can pump sewage, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedsafety requirements ,　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　Fourth,QuaximarpaVertical centrifugal slurry pump, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, pumping rate maximum particle and weight.

　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.Quality Assurance,　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient, the power supply of the submersible pump shall be turned off immediately. Check whether the cable connector, connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose, or whether the fuse is damaged or burnt out　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowsQuaximarpa, flow model selection parameters: outlet diameter, dust, motor power, impeller speed, pumping rate, maximum particle and weight.　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump,QuaximarpaLong shaft submerged slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be