When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle,Suri30408 stainless steel pipe, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.Suri,Prepare materials and tools, prepare corresponding materials and tools, and check whether they match and apply.Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.Dayrut,For example,SuriSus631 stainless steel plate, the price of tons of goods = tons = the result example: the price excluding tax of ton of goods = a ton = ~ the total weight of the known coil weight and price = the coil weight price, the thickness of stainless steel plate & Chi; Width & Chi; Long & Chi; e.g. & Chi; Χ Χ = kg stainless steel plate weight per square meter (kg) calculation formula: specific gravity thickness (mm) width (mm) length (m) stainless steel weight per meter (kg) stainless steel pipe calculation formula: diameter (mm) diameter (mm) (correct calculation of the price difference between burr and trimming of nickel stainless steel . chromium stainless steel) in the market, the price difference between burr and trimming of stainless steel is usually set at a fixed price. For example, it is generally considered in the market that the price difference between burr and trimming of is yuan tons and that of is yuan tons. In fact, this method is not scientific. In fact, the price difference between burr and trimming of stainless steel is different The correct calculation should be like this.At low temperature, ferritic stainless steel pipe has low-temperature brittleness like carbon steel, but austenitic steel does not. Therefore, ferritic or martensitic stainless steel produces low-temperature brittleness, while austenitic stainless steel or nickel base alloy does not show low-temperature brittleness. Sus (Cr) and SUS (cr) of ferritic stainless steel pipe It shows that the impact value decreases sharply at low temperature. Therefore, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, high purification process can be considered. With the help of C and N level, the embrittlement temperature is in the range of - ℃ to - ℃The domestic prospect is promising, and there is a large demand for building water supply pipes. According to the 'Ninth Five Year Plan' of construction and the outline of long-term objectives in , the demand for each pipe is ~ km from to , including km of cold and hot water pipes in residential construction areas. Some people believe that the development of stainless steel water pipes is of great significance to improve the grade of modern urban buildings.

When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price, the reasonable price and perfect service of all kinds of stainless steel plates,SuriStainless steel pipe material, stainless steel coils, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).Someone asked whether the stainless steel pipe was rusted and caused toxic problems? & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).Welcome calls ,During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.Stainless steel pipe, is a new family emerging in the field of pipe materials. It has been widely used in building water supply and direct drinking water pipelines.

Adjust the ratio of austenite forming elements to ferrite forming elements in the steel to make it have austenite + ferrite dual phase structure, in which ferrite accounts for % - %. This dual phase structure is not easy to produce intergranular corrosion.Total quality assurance,Low temperature processing of stainless steel pipe --- martensite series stainless steel is quenched from austenitizing temperature and then cooled to very low temperature to promote martensite quenching. It is suitable for stainless steel easy to produce residual austenite.The Chinese brand of stainless steel plate is crnimoti (CrNiMoTi with paper should also be this brand). The new brand is crnimoti stainless steel plate. The stainless steel plate is added with Ti in SUS steel to improve the intergranular corrosion resistance. It is applied to the equipment of, phosphoric acid, acetic acid and acetic acid. & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).Suri, and shall be supplied according to the scheme.Adjust the ratio of austenite forming elements to ferrite forming elements in the steel to make it have austenite + ferrite dual phase structure, in which ferrite accounts for % - %. This dual phase structure is not easy to produce intergranular corrosion.Stainless steel is usually divided into stainless steel pipe, and its chloride stress corrosion resistance is better than other kinds of stainless steel.

toughness and weldability increase with the increase of chromium content