Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.The inspection items, sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Flourishing,Square pipe, the steel pipe whose ratio of outer diameter to wall thickness is less than is called square pipe. At present, the square tubes produced by qb square tube factory are mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. For transportation: water supply and drainage. For gas transmission: gas, steam and liquefied petroleum gas. For structure: for punchingComprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.Kuresare,According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed), the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube,FlourishingGalvanized square tube customization, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high,FlourishingHow much is a ton of galvanized steel pipe now, it will have a serious impact on the capital after operation. The plant built with qb square pipe, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.

Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.After the square pipe is produced, the surface treatment is generally carried out that is, rust the scale, dirt and attachments on the surface of the square pipe are removed. Those that cannot be treated by physical treatment should be treated by chemical treatment.Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, food, machinery and other industries.Inspection standard,Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality.Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.

Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, light textile,FlourishingPrice of galvanized seamless steel pipe, food, machinery and other industries.Direct labor,Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.It seems that preheating the qb square tube can avoid a lot of problems, and there will be a better guarantee that the qb square tube itself is a quality problem.With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.FlourishingStainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube C-section steel and H-section steel has the characteristics of time saving, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, it will have a serious impact on the capital after operation. The plant built with qb square pipe, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.