which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling

The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).The main way to prevent stress corrosion of austenitic stainless steel is to add SI ~ % and keep the content of N below .% from smelting. In addition, the content of impurities such as P, Sb, Bi and as should be reduced as much as possible. In addition, which does not correspond to stress corrosion in Cl - and oh - media. The initial micro crack will not continue to expand after encountering ferrite phase,The welding performance is also much better than that of ferritic stainless steel. Generally, preheating is not required before welding and heat treatment is not required after welding.Model & mdash; Martensite (high strength chromium steel), good wear resistance and poor corrosion resistance.Kingston,The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.Construction materials shall be prepared and delivered to the site according to the data scheme, and shall be supplied according to the scheme.Austenitic stainless steel heat treatment austenitic stainless steel commonly used heat treatment processes are: solution treatment,IsabelaHow many stainless steel plates, stabilization treatment and stress relief treatment.

For more than years, architects have been using stainless steel to build cost-effective buildings. Many existing buildings fully illustrate the correctness of this choice. Some are very ornamental, in many other applications the role of stainless steel is not so eye-catching, but in the aesthetics and performance of buildings For example, because stainless steel has more wear resistance and pressure resistance than other metal materials of the same thickness, it is the preferred material for designers when building sidewalks in places with large population flow.: stainless steel strip (stainless steel coil): or coil, coil, coil,Isabela06cr18ni11ti stainless steel plate, plate coil. There are many names, and the hardness of the strip varies from dozens to hundreds. The customer needs to determine which hardness to use first. (K mirror luminosity)Bidirectional Product Description: the tensile strength of the material is ~ mpa, and the high working temperature can reach ℃.Respect for customers,The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict, so that the molten salt has strong oxidizing power, low melting point and small viscosity. Only the sodium halo shall be analyzed in the production process, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide, which is easy to be removed during acid pickling. Due to the action of high temperature, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃ time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching, firstly lift the parts basket into the tank, stop above the horizontal plane, close the tank cover, and then lower the parts basket into the water, Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe are stable, safe, reliable and maintenance free. The technical level has reached the domestic level and the international advanced level of similar products until submerged.The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), American code (ACI -) and Japanese code (aij-cft), China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme, and establish quality standards.The continuous casting of stainless steel pipe fittings is generally matched with the refining furnace, which has strict requirements on the chemical composition and temperature of molten steel; In order to prevent secondary oxidation of molten steel, non oxidation protection pouring is required during continuous casting production; Strict requirements for refractory materials such as ladle, tundish, nozzle and submerged nozzle.

At the same time, which are being prepared by Tongji University. All kinds of stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe are qualified. Welcome to telephone inquiry and sincerely invite cooperation! At present, there are stainless steel pipes in Sichuan, Guangdong, Zhejiang, Jiangsu and other places, and the products have become mature. Therefore, the time for application has come.How much is it,The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process this has become a necessary means to improve product quality.In order to protect the welding pool well with argon and facilitate the welding operation, the center line of tungsten electrode and the workpiece at the welding position shall be kept ~ ° Angle, the included angle between filler wire and workpiece surface shall be as small as possible, generally -DEG; about.Model & mdash; Martensite (high strength chromium steel), good wear resistance and poor corrosion resistance.Isabela,Deformation strengthening of austenitic stainless steel stainless steel has good cold deformation performance. It can be cold drawn into very thin steel wire and cold rolled into very thin steel strip or steel pipe. After a large amount of deformation,Isabela317L stainless steel plate, the strength of the steel is greatly improved, especially when rolling in the subzero temperature zone. The tensile strength can reach more than MPa. This is because in addition to the cold hardening effect, there are also superimposed Deformation induced M transition.Application field: launch the market plan of stainless steel pipe in the target market of new products, such as stainless steel kitchen equipment.This material without titanium and niobium has an inherent tendency of intergranular corrosion. Intergranular corrosion can be reduced by adding titanium and niobium and stabilizing treatment. It is a kind of high alloy steel that can corrode in air or chemical corrosive medium. Stainless steel has beautiful surface and good corrosion resistance. It does not have to undergo surface treatment such as color plating to play a role of rust free