Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time this will hide the moisture. Therefore, the outer edge of the wheel hub, the key hole and the wiper frame and other areas should be checked regularly the corner of the bottom of the trunk, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.SichuanThe opening system of the manual hydraulic stacking platform truck is divided into pedal type and manual type for selection, which is simple and easy to operate. The models are divided into fixed and mobile forks, and there are many options for ordinary legs and straddle legs. It is very suitable for warehouse, supermarket retail merchandise placement, and extraction.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Tibati,The water cooling of the hydraulic station is generally tube-type water cooling and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier,SichuanHydraulic lifting cargo elevator, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.

When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.The aluminum alloy lift is simple in design, beautiful in appearance and strong in practicability. It replaces the previous working methods of scaffolding and crane suspension. It has high working efficiency, safety and stability, and low failure rate.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Respect for customers, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.System: explosion-proof electronic control system, remote control system, P IC system.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.

Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .consumption,Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The operating rod is heavy. The operating rod mechanism is faulty. Check, adjust, and replace unqualified parts; clean the valve parts; check the hydraulic oil cleanliness and the valve core is stuck (manufacturing, installation problems,SichuanFixed lifting cargo elevator,SichuanGuide rail lifting cargo elevator cargo elevator, dirt problems)Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Sichuan,In addition, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.