Because of the characteristics of copper itself, it is very easy to rust and corrode in places with high ambient humihumidity. If we often use it, the problem will be smaller but if it is placed for a long time, the copper will be damaged. Many people do not know how to treat the copper surface? Now let the staff answer for you.Disadvantages: Due to loose tissue and high pressure resistance, the pipe is only used to produce small air conditioning copper rods.Lumut,It is applicable to the removal of thin liquid oil stain and light rust and the generation of phosphating film with certain corrosion resistance. See Table for example of formula and operating conditions. Table Degreasing, rust removal, phosphating and passivationRemove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe,LumutRed copper tube, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.Senlar,Insert the pipe into the top of the bayonet,e the sleeve on the pipe to evenly apply the flux on the joint, and confirm that the pipe is inserted into the bottom of the socket, then wipe off the excess flux, and the joint is assembled and can be heated.In the middle and late ten days, although there were good news such as the rise of futures and the increase of production restriction policy in Wu an region, due to the high inventory level, traders had no desire to increase prices, most of them had shipped goods, and spot prices lacked motivation to rise. The market inventory rose significantly. At that time, the market inventory in Handan reached a high level after the festival. The sluggish demand performance for a long time led to the oversupply of the market, and the continuous rise of inventory led to the empty market mentality.Strong connection firmness of copper pipe: the connection between copper pipe and copper fittings is strong.

Tangshan billets rose sharply last weekend, steel mills in some northern cities implemented production restriction, and some domestic economic data improved, which boosted manufacturers confidence. Today, steel prices generally rose. However, with the approaching meeting and the rainfall in the south caused by the typhoon, the construction progress of the downstream construction site is affected, which is not conducive to the continuous demand. The high spot price transaction today is weak, which is difficult to support the continuous rise of steel prices. It is expected that the building materials market will maintain a volatile trend tomorrow, and some businesses may reduce prices and take goods.To prevent core problems of copper tubes, the outlet tempmperature of copper tubes should be well controlled. The cooling capacity of the annealing furnace in the cooling stage should be improved by equipping a refrigeration unit for the annealing furnace, so as to ensure that the outlet temperature of copper tubes does not exceed ℃. By controlling the outlet temperature of copper tubes, the problems of the core of coil tubes and the inner wall of the purging inlet end can be solved.When placing they should be stored separately according to the different components, and should not be mixed together. The copper surface may have electrolytes, so it will react, especially with other materials such as rubber which has a large impact.High quality brand,When welding,Lumutbrass tube, some iron plants do not take orders temporarily. The steel mills in Liaoning have increased their enthusiasm for purchasing steel. The iron mills have delivered well, and the price of raw materials has risen, so the iron price has risen. The iron mills have a high enthusiasm for producing steel, so there is not much cast iron resources,Lumut15CRMO alloy plate, and the price has risen. A few steel mills in Tangshan began to purchase a small amount of steel for smelting, and most steel mills are still on the lookout for inquiry. Under the background of increasing cost and gradual release of demand, the pig iron market is performing well and is expected to continue to operate strongly in the short term.

Insert the pipe into the top of the bayonet,e the sleeve on the pipe to evenly apply the flux on the joint and confirm that the pipe is inserted into the bottom of the socket, then wipe off the excess flux, and the joint is assembled and can be heated.build,The composite method of three production methods of copper tube is also a high-tech production method for this method. It is a copper material containing impurities. Those copper materials, copper alloys and composite copper materials are put together by electrochemical reaction to produce a nanocrystalline copper material, and then the material is purified to produce copper tube materials.Advantages: low investment cost, high output and low price.Although the opening continued the weak trend, the intraday transactions improved, and the prices of some copper bar manufacturers rose. From the specific situation, although the manufacturer feedback that the shipment is average, the mentality is relatively calm, the market inventory is not much, and the manufacturer is not willing to significantly reduce the price. In terms of the market, the transaction of strip steel is better than other steel varieties, and the downstream mainly focuses on callback buying without panic inventory clearing. It can be seen that although the steel market continues to shake, the overall demand for strip steel remains in a good state.Lumut,The second of the five application fields of red copper plate T, red copper row and red copper tube: copper is widely used in the chemical industry to manufacture vacuum vessels, distillation pots, brewing pots, etc.antages: low production cost and high production efficiency.The blowpipe shall be perpendicular to the lead pipe during welding