The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particlesSanto Domingo,　　For the pipeline pump in the workshop, it is necessary to consider whether the pipeline pump is worn to a certain extent due to inadequate maintenance, but the performance of the pipeline pump is degraded. In case of abnormal water absorption during installation, check the motor during installation,　　 Then reinstall the equipment on the engine and install the rubber hose.Muhoroni,　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, and say that the nut is loose

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local places　　Attachment: data sheet required for ordering deep well pump　　The Tao part also consumes part of it.install,Santo DomingoBaigang deep well pump,　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft,Santo DomingoSubmersible slurry pump, and successively install the bearing inner race, bearing gland and retaining sleeve　　 Another possibility is that the gas is sucked in when the pump is in use.

　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerPursuit of excellence,Santo DomingoSmall deep well pump,　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.　　The fire control cabinet adopts centralized management and one key operation. The startup procedure is simple and convenient. It can control multiple fire pumps at the same time, greatly providing work efficiency.　　The whole packing body, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vaneSanto Domingo,　　When the slurry pump is working the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　During adjustment, firstly loosen the support cover then compress the nut, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation