In fact,BaladroSubmersible slurry pump, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Baladro,　　The water pump is not installed firmly or installed too high.　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Ujida,　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking,BaladroSubmersible sewage pump, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　Under the action of auxiliary devices, it can transport the slurry, it can also ensure the internal and external balance of the submersible slurry pump during transportation so that the pressure at both ends of the equipment can be balanced during normal use　　Do not exceed the rated current.

　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.　　 whether pre lubrication water tank is required　　Stability and reliability of seals between pump bodies.How much does it cost?,　　It should be /-/ between. When the packing is worn the packing gland can be properly pressed. If it is worn too much, which are mainly to pay attention to the details and the phenomena occurred during the operation it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged

　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.Sampling inspection,　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　 Ensure that the electric pump operates normally The electric pump needs to be equipped with a fully active water pump control cabinet when there are no other conditions. Do not directly connect the power grid or use a knife switch to connect the power supply.　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certainBaladro,　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s,BaladroLong shaft submerged slurry pump, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance