There are differences.　　Potential energy, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?Desanpalados,　　First of all, the slurry pump is divided into three categories from the installation method: horizontal slurry pump, submersible slurry pump horizontal slurry pump: also known as dry installation slurry pump, because it is installed on the ground and the surface of the pump body cannot contact the slurry, it is called dry installation. When this type of pump is installed,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerChangwon 　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.

　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　Slide evenly and slowly along the guide rail until the active coupling is in place. When the mobile device is selected, the hose shall be sleeved first, and the chain rope shall be threaded into the two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size,DesanpaladosIrrigation deep well pump, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.consumption,　　.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.

　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air,DesanpaladosDrilling fluid slurry pump, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleoffer,　　The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical seal　　The main shaft of the water pump is bent or the main shaft of the water pump and the motor is not concentric or parallel.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorDesanpalados,　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, and the site is cleaner.　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.