The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Ilopango,Clamping operation the jaw of the caliper must be placed perpendicular to the axis of the pipe and pipe fitting, and the convex ring of the pipe fitting needs to be put into the groove of the jaw for clamping. In order to prevent operation, the operator can only stand on the axis of the pipe, not on the left and right sides of the tong head.Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die, and the jaw is perpendicular to the pipe axis.Qapshaghay,Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm, the Rockwell or surface Rockwell hardness tester can also be used to test the hardness of pipes.The corrosion resistance of stainless steel depends on chromium, but because chromium is an integral part of steel, the protection is different.Various welding methods of combined welding stainless steel welded pipe have their own advantages and disadvantages. Combined welding methods include argon arc welding plus plasma welding, high-frequency welding plus plasma welding

After that, the second widely used steel is mainly used in food industry, pharmaceutical industry and surgical equipment. Adding molybdenum makes it obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than stainless steel pipe, it is also used as & ldquo; marine steel & rdquo;. SS is usually used in nuclear fuel recovery devices. Grade stainless steel Steel pipes usually also meet this application level.Low temperature processing --- martensitic stainless steel is quenched from austenitizing temperature and then cooled to very low temperature to promote the quenching of martensite. It is suitable for stainless steel which is easy to produce retained austenite.Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).Installation works,IlopangoStainless steel 304 seamless steel pipe,Stainless steel, precipitation hardening stainless steel and high alloy with iron content less than % are usually named by patent name or trademark.Good ductility used for forming products. It can also be machined to harden rapidly. Good weldability. Wear resistance and fatigue strength are better than stainless steel.Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C, dual phase (austenite ferrite).

All steel with openings at both ends and hollow sections, and with a large ratio of length to section perimeter, can be called steel pipe. When the ratio of length to section perimeter is small, it can be called pipe section or tubular fittings, which belong to the category of pipe products.equipment maintenance ,Stainless steel pipes are divided into ordinary carbon steel pipes, high-quality carbon structural steel pipes, alloy structural pipes, alloy steel pipes, bimetallic composite pipes, coated and coated pipes to save precious metals and meet special requirements. Stainless steel pipes have a wide variety, different uses,Ilopango304 seamless stainless steel pipe, different technical requirements and different production. The outer diameter range of steel pipe currently produced is . & mdash; mm, we specialize in providing quality assurance for L stainless steel pipe s stainless steel pipe and L stainless steel pipe. During the preferential activities, new and old customers are welcome to consult. Steel pipes are usually classified according to the following.Cold rolled oriented silicon steel strip consists of nominal thickness (expanded by times) + code G: ordinary material,IlopangoStainless steel polished tube, P: high oriented material + guaranteed iron loss value (the value after expanding the iron loss value when the frequency is Hz and the large magnetic flux density is T by times). For example, g indicates that the thickness is .mm and the guaranteed value of iron loss is ≤ cold rolled oriented silicon steel strip. Liaocheng Suntory stainless steel provides electroplated tin plate and hot-dip galvanized plate: electroplated tin plate, electroplated tin sheet and steel strip, also known as tinplate. The surface of the steel plate (belt) is plated with tin, which has good corrosion resistance. In addition, it can be used as packaging material for cans, inner and outer sheath of cables, instrument and telecommunication parts, flashlight and other hardware.When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, etc. to change the molten pool temperature so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding so as to facilitate the observation of molten pool and penetration; when filling the welding wire, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.Ilopango,Stainless steel pipe packing bag is nothing more than the function of protecting the surface of stainless steel pipe, so most stainless steel pipe users do not have to question this point.Stainless steel and alloy tool steel (C content is expressed in thousandths), such as thousandth of CrNi (i.e. .% C), stainless C & le; .%, such as CRNI ultra low carbon C & le; .%, such as crnimo.When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .