It will still decrease. The humidification amount will decrease by % at degrees.Precautions for purchase and shipment when using the medical cold storage project,PalmiraFruit cold storage temperature,PalmiraInstallation of cold storage, the speed must be strictly guaranteed during the purchase and shipment of products. If the temperature of the medical cold storage is about degrees, the opening time must be strictly within minutes. If the temperature of the medical cold storage is left and right degrees the opening time can not be too high, strictly within minutes.Palmira,The three-dimensional automatic cold storage adopts computer, which can complete the loading and unloading, stacking, storage temperature and refrigeration equipment operation of the cold storage.Moreover, polyurethane does not produce harmful gas at high temperature.Lui deritz,The wide, light and thin walls are made of rigid polyurethane foam at the same time as structural materials, making the whole structure have the advantages of light weight, large span and high load. The thinner polyurethane sandwich plate can meet the relevant provisions on building energy consumption limit, which allows the use of thinner plates during construction and saves building space.More and more people begin to build cold storage, and most people choose to use cold storage for cold storage construction. Why? Why do people choose cold storage for construction? What are the advantages of cold storage? The following is a detailed introduction.The two sets of connectors between the cold storage shall be wedged tightly, and the two sets of connectors shall be fixed at the upper outer and lower sides of the cracks in the cold storage respectively. The lower connector shall be as close as possible, so as to facilitate the use of concrete to cover the connector in the future.

The product shade warehouse is a warehouse location below ℃ and the sun cannot be straight. The humidity is % ~ % relative humidity, and there are corresponding strict requirements for the wall, ceiling, ventilation, disinfection and epidemic prevention of the warehouse. The refrigeration system adopts full-automatic microcomputer electrical technology and does not need to be on duty. It mainly stores western and Chinese grass materials and instruments, and can monitor and record the temperature and humidity in the storage area.Establish a perfect computer network to realize the scientization of refrigeration supply chain distribution and traceability. In the European Union, the United States and Japan, all members of the food supply chain have the legal responsibility to implement traceability.Install the library body. Generally, the warehouse body can be divided into small warehouse body and large warehouse body. The small warehouse body is basically a combined cold storage assembled with warehouse plate. The large warehouse body is mostly a civil cold storage. The assembled or constructed warehouse body is generally required to be flat, compact and solid, without hollow feeling, load-bearing, antifreeze, moisture-proof, etc.safety requirements ,When hot ammonia defrosting or electric defrosting is selected as the cooling fan, professional cold storage installation, cold storage installation, cold storage construction, fruit preservation cold storage, medical cold storage, safety, environmental protection and economy! The products are exported to foreign countries and are deeply trusted. Defrosting and drainage can be discharged immediately. Electric heat tracing and insulation can be selected for the defrosting and drainage pipeline of the warehouse location.During the installation of polystyrene storehouse, the Perpendicularity Error of wall plate shall be corrected while the top storehouse plate is installed. The length of the top warehouse plate shall be mm shorter than the surface of the wall plate. After the installation of the top warehouse plate, the mm gap shall be marked with foaming material to ensure the sealing performance of the warehouse body.The selection of cold storage is very important for cold storage, because cold storage is different from ordinary cold storage. The temperature in cold storage is usually low, and the air temperature, attention must be paid to the selection of cold storage with better temperature. If the selection of cold storage is not good, the temperature in the cold storage is difficult to, which is easy to cause the deterioration of products in the cold storage, or the refrigeration compressor in the cold storage often works, wasting more resources and increasing the cost.

There should be excellent drainage pipe standard around the warehouse, the soil temperature should be low, there should be interlayer under the cold storage,PalmiraCold storage installation Cold Storage, and maintain good natural ventilation. Maintaining dryness is very important for the cold storage. In addition, the phase electricity of the relative volume shall be built according to the output power of the refrigeration unit. If the cold storage is water-cooled and radiating, the tap water pipeline shall be paved and the FRP cooling tower shall be built.Equipment maintenance,Cold storage, compressor overload, lack of refrigerant, low pressure too low, excessive air intake, compressor jamming.Wires should not be in the open air to avoid long-term sun exposure and wind blowing, wire skin aging, long-term cold storage installation, installation of cold storage, fruit preservation cold storage, medical cold storage without turnover so as to avoid price difference, and the price is % higher than the market price! The price of more than one ton is higher! Short circuit, leakage, etc.For the ground insulation of large cold storage, we can that the ground insulation of medium-sized cold storage is more complex than that of small cold storage, and the ground insulation operation of large cold storage with larger warehouse area will be more complex. The common operations are as follows: first lay the ventilation pipe to prevent the ground from freezing drum cracking, then lay the XPS extruded plate (staggered laying is required when laying the extruded plate), then lay the moisture-proof and vapor barrier on the upper and lower sides of the extruded plate, then pour the reinforced concrete (generally at least cm thick), and then make the emery floor or epoxy floor according to the requirements. Among them, the XPS extruded plate is also laid according to the warehouse temperature. For example, the XPS extruded plate with thickness of ~ mm needs to be laid in the general low-temperature cold storage, while the XPS extruded plate with thickness of ~ mm can be laid in the high-temperature cold storage.Palmira,Install the temporary lighting facilities in the warehouse, install and arrange the construction electrical equipment, and do a good job in rain proof, moisture-proof, anti-collision, anti binding and other safety protection.There are many kinds of cold storage. According to the material it can be divided into color steel plate, stainless steel plate and salted steel. Among them, color steel plate has strong anti rust ability, while salted steel has both beautiful appearance and anti rust ability. According to the layout, it is divided into flat plate and wave plate. The former is flat after the surface material is formed and the latter is rugged after the surface material is formed. According to the thickness and color of surface materials, the thickness of stainless steel is .mm and mm, without color requirements; The thickness of salted steel plate is .mm, without color requirements; The thickness of PE paint baking board is .mm, .mm ivory white, titanium white and white gray. The most important thing for the cold storage is the applicable temperature of the cold storage. It is divided according to the insulation thickness of the storage plate. The thickness of the sky floor of the mm storage plate is mm, and the thickness of the vertical plate is mm and mm, which is suitable for the thermal insulation conditions of ℃ ~ - ℃. The thickness of the ceiling plate and the vertical plate of mm storage plate is mm, there are many other classification methods of cold storage. Determined by the current processing technology it can be divided into standard plate and non-standard plate according to the width and size range of warehouse plate, including standard plate vertical plate width wa = mm, heaven and earth plate width WB = mm, vertical angle plate W = mm, W = mm, W = mm and W = . The dimensions of non-standard plates are different from those of Wa, WB and W.The ultrasonic town is a patented technology with a shaped energy cover, which increases the effective humidification amount by -% per hour. What are the reasonable aspects of the design of the quick freezing warehouse?