Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Chula Vista,　　For /g-g gravel pump, which belongs to large-diameter slurry pump, it is necessary to remove the impeller removal ring and rotate the impeller in the opposite direction.　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impellerMaaseik,　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes volumes and s. Therefore, many people believe that　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators,Chula VistaSplit vertical pipeline pump, especially

　　 It may be that the motor power of the water pump is too large, the working current is too large,Chula VistaVortex pump and pipeline pump, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　The system shall be equipped with a fire control cabinet.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.Online consultation, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable,Chula VistaWater well pipeline pump, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, many people believe that

　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.management,　　.　　 Check the wiring of the motor itself: it may be the high temperature caused by wrong wiring. If the wiring is wrong, quickly connect it back to the correct method.　　When in use, it can drive the impeller to rotate so as to drive it to flow.Chula Vista　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be　　Troubleshooting: first increase the water pressure, then inject water into the pump body and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large