Model & mdash; After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade.Welding of stainless steel pipe argon arc welding stainless steel pipe: it is required to have deep penetration, no oxide inclusion, and the heat affected zone can be as small as possible. Argon arc welding maintained by tungsten inert gas has good compliance, high welding quality and good penetration function. Its commodities are widely used in chemical, nuclear and food industries.Lovech,LovechPrice of 304 stainless steel strip,Windproof and ventilation. Where there is wind, please take measures to block the net, and take appropriate ventilation measures indoors.When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, and the weld on the outer side can be blocked with adhesive tape (see Table ) .Ayakujo,Marking: in order to make the steel pipe complete the socket of the pipe fitting, the length must be marked and marked at the pipe end.Martensitic stainless steels typical martensitic stainless steels include Cr ~ Cr and Cr, which have good processing properties. Deep drawing, bending, crimping and welding can be carried out without preheating. Crl does not require preheating before cold deformation but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, while crcr is mainly used to make surgical and wear-resistant parts of medical instruments; crl can be used as corrosion-resistant bearings and tools.Refining and transportation industries are in great demand. Secondly, geological drilling, chemical industry, construction industry, machinery industry, aircraft and automobile manufacturing, boiler medical equipment, furniture and bicycle manufacturing also need a large number of various steel pipes. With the development of new technologies such as atomic energy, rocket, missile and aerospace industry, stainless steel pipe plays an increasingly important role in national defense industry, science and technology and economic construction.

Combined steel and spring steel, such as CrMnTi simn, (C content is expressed in ten thousandths).The application range is wider than that of ferritic stainless steel. Compared with ferritic stainless steel, duplex stainless steel has the following disadvantages: high alloy element content and relatively high price. Generally, ferritic stainless steel does not contain nickel.For business people, of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases, they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, But I have to accept it. Next,LovechStainless steel pipe 304, xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.Service first,Combined steel and spring steel, such as CrMnTi simn, (C content is expressed in ten thousandths).Body austenitic stainless steel seamless steel pipe and welded steel pipe stainless steel pipe for mechanical structure stainless steel pipe for ordinary pipe stainless steel pipe for boiler, stainless steel pipe for heat exchanger and seamless steel pipe for chemical industry (crnit) qhyad crnimosi duplex stainless steel seamless steel pipe. Stainless steel is mainly used in the automobile industry, accounting for more than % of the total consumption of automobile stainless steel, and % is ferritic stainless steel. The exhaust gas produced by automobile engine is from the rear of intake pipe, front pipe hose, converter and center pipe. The common steel grades of exhaust system are L l, s stainless steel pipe and L stainless steel pipe are provided for a long time. The products are complete, excellent quality and favorable price. The use ratio of stainless steel pipe and welded pipe is about :.Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.

Stainless steel seamless steel pipe for structure (instead of gbt-)OK or not?,The welding of stainless steel pipe is usually composed of backing welding, which is not only related to the quality of engineeringAfter the installation of stainless steel water pipe cleaning pipeline, it is recommended to use % potassium permanganate for disinfection. It is strictly prohibited to use bleaching water for disinfection, and clean it with clean water after disinfection. If it is not put into use for a short time, compressed air must be used to blow out the residual water in the pipe, so as to prevent the corrosion reaction between oxygen free in the pipe and other media. Series & mdash; Martensitic precipitation hardening stainless steel.Lovech,Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C, dual phase (austenite ferrite).After molten steel casting, stainless steel pipe fittings generally adopt the same vertical, vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.No solution treatment. The alloy elements do not dissolve into the matrix, resulting in low alloy content and poor corrosion resistance.