Now you know the reason why the pump has air turbidity. In fact,BaltimoreRubber lining submerged slurry pump, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.Baltimore,　　 Check the voltage to see if the voltage is too low to drive. Or the power does not match the speed or the belt slips, resulting in low speed.　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.Alaghsas,　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact such measurement is not very accurate.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.

　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　The key to the problem should be to fundamentally solve the problems of pump sealing and overload, which is a more active method. Therefore, we applied the hydrodynamic seal technology of the auxiliary impeller and the non overload design technology of the pump to the submersible sewage pump, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), and dry it naturally.Free consultation,　　 First of all we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use,BaltimoreUsed pipeline pump, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.Installation materials,　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 pump room height and allowable lifting height of lifting equipment　　When in use, it can drive the impeller to rotate so as to drive it to flow.Baltimore,　　Superior, reasonable structure,BaltimoreSubmersible non clogging slurry pump, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.