In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation,ProvFloor to floor cargo elevator, and to prevent unnecessary wear and tear.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Prov,Remove and disassemble the descending valve of the hydraulic elevator, blow off the plunger with compressed air, then install it and install it again.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other,ProvGuide rail hydraulic lifting cargo elevator, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Nykobing Falster,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.

The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today the editor will simply popularize the knowledge for everyone.Avoid, especially during storage. Store in a cool, dry place, and avoid rain and snow during work.In addition to the fixed mode the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, the scope of operation is not limited to a certain place, when installing outdoor advertisements, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.wholesaler,The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.

Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Sales Department,Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.In our daily life today, the application of hydraulic lifts is becoming more and more extensive, and it is deeply loved by customers. As a lifting tool, the maintenance of lifts must not be sloppy. The following editor will introduce the daily maintenance of hydraulic lifts .What types of lifts are there? There are many types of this equipment, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production,ProvLifting cargo elevator 1 ton, a special lifting device is required to be fixed at a certain position of the production line.Prov,What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.