Start the priming pump. Moreover, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　The whole packing body, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve,BokoAh slurry pump, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vaneBoko　　Conduct a comprehensive preventive maintenance once a year, including: replace all O-ring seals; Check the bearing wear and add new grease; Check the wear condition of the mechanical seal to determine whether it needs to be replaced; Check the wear of the impeller and the seal between the impeller and the pump body　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlySabana-Yegua,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.

　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　 rotate the impeller to check whether it is flexible, and check whether the seals at the pump vent hole water drain hole, oil drain hole and cable joint are loose. If they are loose, they must be tightened.　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.Home page recommendation,　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body

　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced and the income has been increased.Welcome calls ,　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, which makes the flow increase after the impeller is cut.　　If there is a fault, it is inconvenient to repair.　　With water, you can start working.Boko,　　In addition to the method, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well,BokoFire deep well pump, which should be a comprehensive optimization design method.　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　In the mud pump,BokoWQ submersible pump parameters, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller