in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor andNew Guinea,　　In terms of performance parameters, optional flow range: - (m/h), lift range: - (m), power range: .- (kw), caliber range: - (mm).　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.Ponte do Lima,　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.

　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　 Low vibration and noise, low motor temperature rise, no pollution to the environment.　　 If the hot water within ℃ is recommended, the hot water pump must be used and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.Online consultation,　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise,New GuineaWear resistant slurry pump, so in fact such measurement is not very accurate.　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use

　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.Supply chain quality management,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close,New GuineaVertical non clogging sewage pump, but in fact,New GuineaSubmersible non clogging slurry pump, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　D. G-type slurry pump is a single pump shell structure, that is, light weight. The pump body, cover and impeller shall be made of strong wear-resistant high chromium alloy or wear-resistant alloy steel, and the hardness shall not be lower than hrc. The connection of pump body and pump cover adopts special clamping structure, and the pump outlet direction can be rotated freely,　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.New Guinea,　　 First remove the pump from the engine.　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.