The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Clarington,The calculation method theory of square tube mechanics is feasible to calculate static structures, such as warehouses, houses and bridges, but it is not suitable for moving components such as wheels. At this time, people often use the plastic theory. The research of the plastic theory can be traced back to . In , the European Design Association formulated D plastic design code, which is mainly used for plane beams under static load and bending stress For the frame structure with stress, the requirements are as follows:% sigma; B% sigma;% zeta;% ge;% delta;% ge; % for high-rise buildings, more detailed calculation is required. In the case of plastic design, the allowable stress is usually calculated according to the safety factor that the allowable stress is not less than the dynamic load and multiplied by the allowable stress. In the case of bending of an axis, the formula a = w can be used Using plasticity instead of calculated strength can improve the bearing capacity of members by %.The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.Kaele,After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, the adobe has cracks due to the action of thermal stress, and there are cracks after rolling.Hundreds of degrees Celsius, which can save energy.

There are many ways of ignition such as arc, electric spark, flame, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.Shot blasting and sand blasting are widely used in repair and shipbuilding industry. However, whether shot blasting or sand blasting, compressed air is used. Professional square pipe, square rectangular pipe, seamless square pipe, galvanized square pipe,Clarington42 galvanized square pipe, galvanized pipe has high pressure resistance grade, good waterproof performance,ClaringtonGB galvanized square pipe, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. Of course it is not shot blasting, so it is necessary to use high-speed rotating impeller. In the repair and shipbuilding industry, shot blasting (small steel shot) is mostly used in square pipe pretreatment (rust removal before coating); Sand blasting (mineral sand is used in repair and shipbuilding) is mostly used in formed ships or sections to remove the old paint and rust on the square tube and repaint it. In the repair and shipbuilding industry, the main function of shot blasting and sand blasting is to increase the adhesion of square tube coating paint.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.assets,B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.The general delivery length of qb square pipe is mm-mm,ClaringtonStandard for galvanized square pipe, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeNormalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.

Pull square tube:Good quality,The floating mandrel mill is in its heydayAt the same time, the billet of the square tube will be burned and decarburized, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.Pull square tube:ClaringtonCarbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).Stage ( & mdash; )Hundreds of degrees Celsius, which can save energy.