When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　With the continuous development of slurry pump technology submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Frat,　　 Pipeline high-temperature oil pump, pipeline high-temperature chemical pump,FratSmall deep well pump, pipeline high-temperature hot water pump. These models are designed to be formed on the basis of adding water cooling units, and the operating temperature can be as high as degrees or higher.　　The packing seal, auxiliary impeller seal and mechanical seal are mainly used. Among them, the packing seal needs small leakage and is not suitable for transporting toxic, corrosive and precious liquids; The sealing of the auxiliary impeller relies on the reverse pressure of the two sealing impellers during rotation to prevent the leakage of the medium,FratQJ submersible pump, and can also play a role inCosta-Rica　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.

　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm　　There are main reasons why the submersible pump is 'sick'. The rotation direction of the motor is wrong: please ensure that the rotation direction of the motor is correct before using the submersible sewage pump. Even if water is produced by reverse rotation, the output of water is small and the current is large. Direction rotation will cause irreversible damage to the motor winding　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.Bidding,　　Extend service life. In fact, and there is a very important component water seal in the pump, which can separate the pump body from the motor,FratIrrigation deep well pump, so it mainly plays a role in use　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure breakage, etc.

　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.Quotation sheet, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　Clean up the silt and other obstructions in or around the water pump.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.Frat,　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.