The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Stress corrosion cracking (SCC) refers to the cracking caused by the combined action of stress corrosion stress (mainly tensile stress) and corrosion of austenitic stainless steel Austenitic stainless steel is prone to stress corrosion in corrosive media containing chloride ions. When the Ni content reaches % - %, it is a long-term enterprise engaged in stainless steel plate stainless steel coil, stainless steel belt and stainless steel pipe. Welcome to consult. The stress corrosion tendency of austenitic stainless steel is very large. Continue to increase the Ni content to ~ %, and the stress corrosion tendency gradually decreases until it disappears.Coamo,The corrosion resistance of corrosion-resistant stainless steel plate mainly depends on its alloy composition (chromium, nickel, silicon, aluminum, manganese, etc.) And internal structure, which mainly acts on chromium. Chromium has high chemical stability, can form a passive film on the steel surface, isolate the metal from the outside, protect the steel plate from oxidation and increase the corrosion resistance of the steel plate. After the passive film, the corrosion resistance decreases.Therefore, the field with high utilization rate of stainless steel with high competitiveness and comprehensive quality will also be an important part of the plan.Kyongsan,Austenitic stainless steel heat treatment austenitic stainless steel commonly used heat treatment processes are: solution treatment,Coamo0.5mm stainless steel strip, stabilization treatment and stress relief treatment.Typical ferritic stainless steels are Crl, Cr and Cr.Austenitic stainless steel is generally used for manufacturing and manufacturing chemical equipment components, low-temperature equipment components in refrigeration industry, and can be used as stainless steel spring and clock spring after deformation strengthening.

No solution treatment. The alloy elements do not dissolve into the matrix, resulting in low alloy content and poor corrosion resistance.Hot rolled stainless steel tubes are generally produced on automatic tube rolling mills. After inspection and removal of surface defects, the solid pipe blank is cut into the required length, centered on the end face of the perforated end of the pipe blank, and then sent to the heating furnace for heating and perforated on the piercer. During perforation, it rotates and advances continuously. Under the action of roll and plug, a cavity is gradually formed inside the pipe blank, the wall thickness of the whole machine is adjusted and the diameter is determined by the sizing machine to meet the specification requirements. It is advanced to produce hot rolled seamless steel pipe by continuous pipe mill.The bright nickel layer on the stainless steel pipe is a silver white metal with slight yellow light. Its hardness is higher than that of copper, zinc, tin, cadmium, gold and silver, but lower than that of chromium and rhodium. Bright nickel has high chemical stability in air and good stability to alkali. Using Brightener on stainless steel pipe,CoamoWhere is stainless steel plate 304, bright nickel can be directly plated without polishing, wear resistance and leveling of the surface make the appearance of stainless steel pipe consistent with other nickel plated parts, and avoid the corrosion of potential difference between stainless steel pipe and other bright nickel. After using bright nickel solution for a period of time, due to the of brightenerproject,Stress corrosion cracking (SCC) refers to the cracking caused by the combined action of stress corrosion stress (mainly tensile stress) and corrosion of austenitic stainless steel Austenitic stainless steel is prone to stress corrosion in corrosive media containing chloride ions. When the Ni content reaches % - %, it is a long-term enterprise engaged in stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe. Welcome to consult. The stress corrosion tendency of austenitic stainless steel is very large. Continue to increase the Ni content to ~ %, and the stress corrosion tendency gradually decreases until it disappears.The bearing capacity of decorative stainless steel pipe ice load is the main control load of offshore platform in severe cold area, which has high requirements for the shear bearing capacity of jacket leg of offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. A compound forming process of double-layer stainless steel pipe for primary circuit main pipeline of station is designed, which solves the problem of limited length of finished products in traditional forging or casting process, and meets the special requirements of complex working environment on pipeline performance. The three roll cross rolling forming process of double-layer casing with outer layer -n austenitic heat-resistant stainless steel and inner layer cr-ni martensitic heat-resistant stainless steel was simulated and optimized by using DEFORM-D finite element simulation software. The internal and external deformation, stress-strain field and temperature field of double-layer stainless steel pipe were analyzed, and the optimal deformation parameter combination was obtained by orthogonal test. The simulation results show that in the process of three roll cross rolling, the large values of equivalent stress, equivalent strain and temperature are concentrated in the area between the outer tube and the roll, and the overall performance parameters of the outer tube are greater than those of the inner tube. The range analysis and variance analysis of orthogonal design test show that the optimal deformation parameter is rough rolling temperature deg; C. Feed angle & deg;, Roll speed: rmin. Objective to improve the existing connection mode of the braking system pipe system of railway freight cars, and accurately shape the end of the stainless steel pipe, so as to obtain the forged joint with better mechanical properties. According to the connection mode of the original pipe system and the plastic forming characteristics of steel pipe,CoamoStainless steel special-shaped pipe, a multi-step upsetting and extrusion process for the end of stainless steel pipe is proposed. The process is numerically simulated by DEFORM-D three-dimensional finite element simulation software, and the forging forming process is analyzedModel & mdash; After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade.

Stainless steel has two classifications: one is divided into chromium stainless steel and chromium nickel stainless steel according to the characteristics of alloy elements; The other is divided into m stainless steel, f stainless steel, a stainless steel and A-F duplex stainless steel according to the microstructure of steel in normalized state.Industry management,Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.　　· Sewage treatment system.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Coamo,The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Stainless steel pipe can be divided into equal section pipe and variable section pipe according to the profile shape. Variable section pipes include conical pipes, stepped pipes and periodic section pipes.During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity