As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Levis,In addition, galvanized steel is more expensive than ordinary steel pipes, so installing them requires a lot of financial costs.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.Kati,The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage. Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.

I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.During the heating and cooling process of structural welded pipe workpiece, due to the inconsistent cooling speed and time of surface layer and core layer, the temperature difference will be formed, resulting in uneven volume expansion and contraction, resulting in stress, and the shrinkage is greater than that of the core layer the starting temperature of the surface layer is lower than that of the core layer, making the core layer stretch. At the end of cooling, the surface layer is compressed and the core is stretched because the cooling volume contraction of the core cannot be carried out freely. That is, under the action of thermal stress, the surface of the workpiece is compressed and the core is pulled.Mixed Scabs are distributed periodically and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.how,LevisInconel 718 Alloy Pipe,Application characteristics of I-beam:After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.

The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Potential development,H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, series and models are complete, which is convenient for settingStraight seam welding is adopted for larger diameter welded pipe, and spiral welding is mostly adopted for large diameter welded pipe; According to the top appearance of seamless steel pipe it is divided into annular welded pipe and special-shaped (square, pitch etc.); according to different materials and main purposes, it is divided into mining anti liquid transportation welded steel pipe, hot-dip galvanized welded steel pipe for bottom pressure liquid transportation, continuous conveyor idler electric welded steel pipe, etc. it is arranged from small to large according to diameter * wall thickness according to the specification, model and dimension table in the current standard.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Levis,After isothermal quenching treatment, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.Defects of alloy pipe and solutions:It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components,LevisHow much is the rebar labor per square meter?, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.