How to avoid this situation when the equipment is in use.　　When the pump is not in use the pump shall be lifted away from the water source in time to drain the accumulated water in the pump,monterey Circulating hot water pipeline pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionmonterey 　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　After that,monterey Vertical heavy-duty slurry pump,monterey Self priming slurry pump wholesale, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.Kampong Pangkal Kalong, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to

　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.　　The key to the problem should be to fundamentally solve the problems of pump sealing and overload, which is a more active method. Therefore we applied the hydrodynamic seal technology of the auxiliary impeller and the non overload design technology of the pump to the submersible sewage pump, which greatly improved the pump seal　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumpingEncyclopedic knowledge,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　It is also necessary to clean the ventilation duct to avoid blockage.

　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Energy costs, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　 the float switch can automatically control the start and stop of the pump according to the required liquid level change, without the need for special personnel, which is very convenient to use.　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.monterey ,　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated