The water resistance is reflected by the water absorption thickness expansion index. If the index value is high, the water resistance is poor, that is, it is easy to cause size change in humid environment.Must not listen to the misleading such as waterproof floor, only moisture-proof floor, no waterproof wooden floor.Fourth, wear resistance means that it is not easy to scratch with artifact.Lessbridge, it&#;s better to lift it. In terms of color matching, light color furniture can be freely composed with thick and light color floors. It is proposed to match warm color floors to look warm and tidy;However, the matching of dark furniture and dark floor should be particularly careful to prevent the depression of 'black autumn wind'.Chelmsford,The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way,LessbridgeSPC floor wear resistance, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.The cross section of the floor is rubbed with a file, so that the heat generated in the cross section is the full volatilization of formaldehyde (formaldehyde will accelerate the release above ℃, and some irritating smell can be smelled). At this time, you can smell it. Generally you can smell three different levels of smell:The surface is treated with special technology, without air holes and water impermeability. It is no problem to shop in the areas where toilets and kitchens communicate with water.No, it will not be like the ordinary wooden floor. Once it bubbles, it will deform and bubble, or it will become moldy due to high humidity.

Feature editing voiceIn daily life, if you accidentally drop the lifting objects and appliances on the wooden floor, or there are small stones on the sole of your shoes walking on the wooden floor,LessbridgeExterior wall waterproof board, the surface of the wooden floor will be damaged to varying degrees and the paint on the floor surface will be damaged. The owners of residential areas must take precautions,It is recommended that customers place a blanket anti-wear layer in the outdoor entrance and room: the anti-wear layer is made of surface paper pre impregnated melamine epoxy resin and metal composite, which is an important part of determining the service life of anti-static floor.The anti-wear layer grants the key physical and organic chemical characteristics of strengthening the anti-static floor surface, such as wear resistance, smoke burning resistance, environmental pollution resistance, corrosion resistance and waterproof. It also happens that this feature constitutes many advantages of strengthening the anti-static floor different from the lacquer wood floor, which not only meets the requirements of contemporary people for home decoration, but also reasonably saves cleaning timeConvenient customers quickly enjoy a high sense of rhythm of daily life.The core layer of WPC wood floor is thicker than that of SPC floor.WPC boards range from to mm,qualityIn today&#;s building materials industry while SPC boards range from to mm.Installation requirements,LessbridgeWear resistant floor leather, there are many incidents of profiteering and even damaging the interests of consumers. The bad atmosphere has led to the reduction of consumer trust.The price is in a state of confusion, and consumers are confused. They don&#;t know whether their pay is worth it. Therefore, they all want to know that there is a relatively transparent price.The real wood floor is processed with a whole plate, with natural texture, and its section texture can correspond to the surface texture one by one;Fake solid wood floor is mostly pasted with leather or stickers on the fake floor, so the cut texture is not commensurate with the surface texture.

The road surface is warm for commercial use. Can we use solid wood floor to make the road surface?Welcome calls In short, floor leather is a layer of synthetic plastic decorative products. In addition to many advantages such as wear resistance, corrosion resistance, moisture resistance, small water absorption simple construction, convenient maintenance and low price, it also adds the advantages of comfortable foot feeling, warm in winter and cool in summer of wood floor, narrowing the gap between wood floor and wood floor. No wonder floor leather will be so popular.If you are also worried about the shortcomings of wood flooring, you might as well consider floor leather materials.Plastic floor leather has the advantages of light weight, good mechanical strength, good foot feeling strength, foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation self extinguishing, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, factories with high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor leather is m ~ m, the width is mm ~ mm, brush the first finishing coat and dry it.After - floors are assembled on the flat ground, observe whether the processing accuracy is flat and smooth, whether the tenon and groove bite is appropriate, not too loose or too tight by hand and eye observation.At the same time, carefully check the assembly height difference and gap between floors.Lessbridge,How to prevent cracks in wooden floors.Precautions for solid wood floor installation : prevent keel from drying. Identify from the package