there will be thinning

During the pushing process of spot welding and repair welding elbows, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.Jukapa,The square tube represents the large capacity of the metal material under the action of tension, and the calculation formula is: where: FB -- the strong force borne by the sample when it is broken, n (Newton); So -- original cross-sectional area of sample, mm. Yield point (& sigma; s) the stress of metal material with yield phenomenon when the specimen can continue to elongate without increasing (keeping constant) the force during the tensile process, which is called the yield point.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, weldability, cold and hot workability and corrosion resistance,Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity the carbon content generally does not exceed %. In addition to iron and carbon,JukapaHow much is 200 galvanized square tube, the main elements of steel also include silicon manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes,JukapaSeamless galvanized steel pipe manufacturer, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust, agent and similar organic matter, but it can not remove rust, scale, welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.

The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.The advantages of real bending are small reverse, accurate forming, and as long as the roll shape is accurate, the R of inner corner forming is more accurate.Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column, large-diameter qb square tube wall thickness classification, large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel,JukapaHeat zinc square tube, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.Focus on Development,Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference so the steel surface treatment requirements are very high.

Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.For more, please check,Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, square tube is generally divided into sections, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products, etc.Jukapa,Square tubes for low and medium pressure boilers (gb-) are high-quality carbon structural steel hot-rolled and cold drawn (rolled) square tubes for superheated steam tubes, boiling water tubes for low and medium pressure boilers of various structures and superheated steam tubes, large smoke tubes, alloy steel and stainless heat-resistant steel square tube for the heating surface of water tube boilers with high pressure and above. High pressure square tube for chemical fertilizer equipment (GB - is a high-quality carbon structural steel and alloy steel square tube suitable for chemical equipment and pipelines with working temperature of - ~ ℃ and working pressure of ~ mA.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different production