Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Fushkruger,The qb square tube rolled from the strip steel through process treatment is generally to unpack, flatten, then roll the round tube into a square tube, and then cut it to the required length. Nowadays, the forming of qb square tube has solid bending and empty bending. The bending degree of qb square tube shall not be greater than mm per meter, and the total bending degree shall not be greater than the actual bending of the total length. As the name suggests the bending is compacted,Fushkruger120 galvanized square pipe, and the internal and external rollers and the internal and external walls of the tube blank are compacted in both directions during the actual bending.Strength QB square strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe is rolled in the annular pass composed of variable cross-section circular hole groove and fixed conical plug. Cold drawing is usually carried out on single chain or double chain cold drawing machine. This method is to put the heated pipe blank in a closed cylinder, and the perforated rod and rod move to extrude the part from the smaller die hole. This method can produce steel pipe with smaller diameter.Coronia del Sacramento,In this period, the technology of continuous rolling pipe was not mature.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore the place must be clean,FushkrugerDN80 galvanized water pipe, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.

Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.The performance advantage of square tube after calcium treatment requires not only high strength, but also good machining performance. For sulfur-containing square tube, sulfur can improve the machinability of steel,FushkrugerSpecification and model of galvanized pipe, so the sulfide inclusion in square tube is the key to determine the quality of steel. Sulfur mainly exists in the form of MNs in the steel. The single MNS inclusion is light black strip. The inclusion with this morphology cuts off the continuity of the steel matrix and makes great differences in the anisotropic properties of the steel. Calcium treatment of molten steel can inhibit the formation of MNS inclusions and combine MNS with al CAS to form composite spindle inclusions. Such inclusions can improve the machinability of steel and avoid the adverse impact of MNS inclusions on the properties of steel.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.wholesaler,High quality steel (P & le; .%, S & le; .%)The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.

C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.Quality assurance,After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference,Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.Compared with other welding square pipe welding has many advantages, the material only needs to be heated below the melting point

mainly because of the exothermic reaction