So flat and the size and thickness are not standardized, it can reflect that this square tube is a poor product& rdquo;The floating mandrel mill is in its heydayKingston Park,In the case of dynamic load, plastic design usually calculates the allowable stress according to the safety factor that the allowable stress is not less than the dynamic load and multiplied by the allowable stress. In the case of bending of an axis, it can be calculated by the formula a = W. replacing the calculated strength with plasticity can improve the bearing capacity of the member by %.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe which can remove loose or oxidized scale, rust, welding slag, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.Kosovo Polje,Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Main uses of square tube: square tube is mainly used in tap water engineering petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.For structure: as pile driving pipe and bridge; pipe for wharf, road and building structure, marine pile driving pipe, etc.

C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Hot rolled qb square tube continuous casting slab or blooming slab is used as raw material, heated by stepping heating furnace and descaled by high-pressure water into roughing mill. Roughing material enters finishing mill after head cutting, tail cutting and then computer rolling. After final rolling, it is rolled into straight hair coil through laminar cooling and coiler. The head and tail of straight hair curl are often tongue shaped and fish tail shaped, with poor accuracy of thickness and width, and there are often defects such as wave shape, hem, tower shape and so on. The coil weight is heavy and the inner diameter of the steel coil is mm.Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products, etc.Highly recommended,If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed), the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times),Kingston ParkGalvanized square pipe joint, and propose acceptance with a new batch.We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.The technology of floating mandrel and square tube is gradually mature.

When sand blasting or manual mechanical derusting is used, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the main indexes of the paint must be rechecked before use,If the test results of square tubes fail to meet the provisions of product standards,Kingston ParkGalvanized strip pipe, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.In short, the square tube production process includes these processes: tube blank & mdash& mdash; Cut off & mdash& mdash; Heating & mdash& mdash; Perforation & mdash& mdash; Pipe rolling & mdash& mdash; Sizing (reducing) & mdash& mdash; Straightening & mdash& mdash; Cut head and tail & mdash& mdash; Inspection & mdash& mdash; Packaging & mdash& mdash; Warehousing.The inspection items, sampling quantity, sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Kingston Park,Engaged in square tube, square rectangular tube, seamless square tube galvanized square tube,Kingston Park50 galvanized round pipe, old brand galvanized tube, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.The disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot, billet or square tube Make materials of all shapes, sizes and properties we need.