The continuous casting of stainless steel pipe fittings is generally matched with the refining furnace, which has strict requirements on the chemical composition and temperature of molten steel; In order to prevent secondary oxidation of molten steel, non oxidation protection pouring is required during continuous casting production; Strict requirements for refractory materials such as ladle, tundish, nozzle and submerged nozzle.Deburring: after the pipe is cut off, the burr shall be removed to avoid cutting the sealing ring.Raleigh,　　— Martensite (high strength chromium steel), good wear resistance and poor corrosion resistance.Stainless steel pipe factory stainless steel products are widely used in hardware products, furniture mechanical structure, precision medical instruments mechanical accessories, such as furniture, machinery medical oil, natural gas, water,RaleighStainless steel pipe cleaning, gas, steam and other industries.Mercedes,Model & mdash; other properties are similar except that the risk of weld corrosion is reduced due to the addition of titanium.The experimental ice load of concrete decorated stainless steel pipe is the highest in the cold areaThat is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.

When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .It is generally suitable for the welding of thin plates below mm, with the characteristics of beautiful weld formation and small welding deformation.Good ductility, used for forming products. It can also be machined to harden rapidly. Good weldability. Wear resistance and fatigue strength are better than stainless steel.Statistics,When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature,RaleighPerforated stainless steel disc, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop,RaleighPlate embossed stainless steel, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.The back is not protected by argon, and the flux cored wire + TIG process has been applied in China for several years. Flux cored wires such as et-elt-et-elt-t-et-elt- have been produced and applied to field welding, and good economic benefits have been obtained.It has the characteristics of high efficiency and low cost. At the same time, it can also well ensure the welding quality (in the capacity expansion and reconstruction project of Urumqi petrochemical, we use this method to weld joints and repair joints, with a one-time qualified rate of welding), which is worthy of our use.

AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, due to the high Cr content, it is easy to form & sigma; Pay attention when using.property right,Water preparation, storage, transportation, purification regeneration, seawater desalination and other water industry excellent materials. The demand is about tons.Physical properties the total heat transfer coefficient of metal depends not only on the thermal conductivity of metal, but also on other factors. In most cases, the heat dissipation coefficient of film, rust scale and the surface condition of metal. Stainless steel can keep the surface clean, so its heat transfer is better than other metals with higher thermal conductivity. Liaocheng Suntory stainless steel provides the technical standard of stainless steel plate Stainless steel plate high-strength stainless steel plate with excellent corrosion resistance bending workability, toughness of welding parts and stamping workability of welding parts. Specifically, Mn, P, s, Al and Ni with an appropriate content of less than .% of C, less than .% of N, more than % of Cr and less than % shall meet & le; Cr Mo Si & le; & le; Ni (c n) . (Mn Cu) & le; Cr . (Ni Cu) Mo & Ge; , . & le; C, n & le; . stainless steel plate is heated to ~ ℃, and then cooled at a cooling rate of more than ℃ / S. in this way, it can become a high-strength stainless steel plate with martensite content of more than %, high strength of more than mpa, corrosion resistance and bending processability, B, etc High stamping performance of welded parts.During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity, so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Raleigh,Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, nitrogen fertilizer and chemical pipelines.In order to ensure the appearance quality of continuous casting slab, select appropriate maintenance slag; During continuous casting, the vibration marks formed on the surface of continuous casting slab due to the vibration of mold shall be; Electromagnetic stirring must be used in continuous casting of ferritic stainless steel pipe fittings.Flux coated welding wire (self shielded welding wire) shall be used for backing TIG welding.